Parts for Maytag MLE22PDAGW0: Control Panel Parts

This wire harness routes power and signals between a unit's control and electrical components, restoring reliable electrical connections for proper operation. It replaces a damaged or burnt harness to help resolve intermittent power or control issues. What it does:

• Carries power and control signals between the control board and major components
• Replaces frayed, burnt, or broken wiring that can cause intermittent operation
• Helps eliminate electrical shorts that can trip breakers or blow fuses
• Restores secure connector connections that can cause component failures or no-power symptoms

• One complete wire harness as shown

• Disconnect all power before starting work to avoid shock or equipment damage
• Compare the new harness to the original for matching connectors, lengths, and terminal types
• Route and secure wires away from sharp edges and high-heat areas; use existing clips and ties where present

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

This lid lock assembly secures the washer lid during operation so the machine can run safe wash and spin cycles. It replaces a worn or failed lock to help restore normal cycle starts and safety interlock function. What it does:

• Secures the lid/door so the washer can start and complete wash and spin cycles
• Prevents the washer from operating when the lid is open or the lock is not engaged
• Commonly replaces locks that are broken, won't latch, or cause the washer to not start or not spin
• Works with the washer's control system to confirm the lid is closed before allowing operation

• Disconnect power (and water, if applicable) before starting any repair
• Basic hand tools are usually required; some models require removing the cabinet or top panel
• Verify proper latch engagement and test a short cycle after installation

This replacement cover restores the appliance's exterior finish while protecting internal components from dust and debris. It fits into the cabinet opening to secure and conceal underlying parts for safe, clean operation. What it does:

• Protects internal components and wiring from dust, lint, and accidental contact
• Restores a finished appearance when a panel is cracked, warped, or missing
• Prevents small items from falling into the appliance cavity
• Reduces rattling from loose or missing panels

• One replacement cover

• Disconnect power (and water if applicable) before starting any repair
• Basic hand tools (screwdriver) may be required to remove fasteners or retainers
• Align tabs or slots, then secure fasteners without overtightening to avoid cracking

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

A short self-tapping screw used to fasten appliance panels and trim so components stay secure and aligned. Replacing a worn or missing screw restores proper fit and reduces rattling or loose parts. What it does

• Fastens panels, trim, and small assemblies to the appliance frame
• Keeps control panels, access panels, and bezels securely mounted
• Replaces stripped, rusted, or missing fasteners that cause vibration or rattling
• Helps maintain proper alignment of removable panels and covers

• One short self-tapping screw

• Disconnect power before working on the appliance to avoid shock or injury
• Use the correct screwdriver and hold parts in place while installing to avoid cross-threading
• Do not overtighten — stop when the panel is snug to prevent stripping or cracking
• Replace with the exact part number to ensure proper fit and function

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.