Parts for Maytag MLE22PNAGW0: Control Panel Parts

This wire harness routes power and signals between a unit's control and electrical components, restoring reliable electrical connections for proper operation. It replaces a damaged or burnt harness to help resolve intermittent power or control issues. What it does:

• Carries power and control signals between the control board and major components
• Replaces frayed, burnt, or broken wiring that can cause intermittent operation
• Helps eliminate electrical shorts that can trip breakers or blow fuses
• Restores secure connector connections that can cause component failures or no-power symptoms

• One complete wire harness as shown

• Disconnect all power before starting work to avoid shock or equipment damage
• Compare the new harness to the original for matching connectors, lengths, and terminal types
• Route and secure wires away from sharp edges and high-heat areas; use existing clips and ties where present

Fix unresponsive buttons or a blank display with this laundry center control panel. Restores full cycle selection and settings control. Moderate DIY repair.

Wire harness for laundry center units. Connects electrical components between washer and dryer sections. Replace if wires are frayed, damaged, or broken.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Fix a washer that won't start or stops mid-cycle with this lid lock assembly. Restores safety interlock function for normal wash and spin cycles.

This is a coin box used in commercial or coin-operated dryers. It collects coins deposited by users to activate the drying cycle. Replace this coin box if it is damaged, jammed, not accepting coins properly, or if the locking mechanism is broken.

This metal mounting bracket secures a switch in place inside the dryer. It ensures the switch stays properly aligned and makes reliable electrical contact during operation. Replace this bracket if it is bent, broken, or missing, which can cause the switch to become loose or the dryer to malfunction.

Access panel cover for laundry center. Replaces cracked, broken, or missing covers that expose internal components. Secures cabinet opening for clean look.

Control panel bezel for laundry center units. Replaces cracked, broken, or discolored bezels around the control area. Restores appearance and finish.

Replace your dryer's wire harness if the wiring is frayed, damaged, or has broken connectors. This internal harness connects electrical components.

Wire harness for laundry center units. Connects electrical components between washer and dryer sections. Replace if wires are frayed, damaged, or broken.

This factory screw secures panels, brackets, and other components in your appliance. Replace a missing, stripped, or corroded fastener to restore a tight fit and keep parts properly aligned and rattle-free.

• Secures appliance components and panels in their mounting points
• Replaces damaged, stripped, or missing hardware
• Helps reduce rattling or vibration from loose parts

• Disconnect power; shut off water or gas supplies if applicable
• Match location with the original screw; start threads by hand to avoid cross-threading
• Tighten until snug; do not over-torque, especially into plastic or thin metal
• Reinstall any covers or panels and test for secure fit

A short self-tapping screw used to fasten appliance panels and trim so components stay secure and aligned. Replacing a worn or missing screw restores proper fit and reduces rattling or loose parts. What it does

• Fastens panels, trim, and small assemblies to the appliance frame
• Keeps control panels, access panels, and bezels securely mounted
• Replaces stripped, rusted, or missing fasteners that cause vibration or rattling
• Helps maintain proper alignment of removable panels and covers

• One short self-tapping screw

• Disconnect power before working on the appliance to avoid shock or injury
• Use the correct screwdriver and hold parts in place while installing to avoid cross-threading
• Do not overtighten — stop when the panel is snug to prevent stripping or cracking
• Replace with the exact part number to ensure proper fit and function

Mounting bracket for laundry center units. Secures components in place during operation. Replace if cracked, bent, or missing to restore proper support.

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.