Parts for Whirlpool WOD51EC7HW20: Control Panel Parts

Fix an unresponsive wall oven control panel or cycles that won't start with this electronic control board. Restores proper operation and timing.

Fixes blank display, unresponsive controls, or incorrect oven temperatures. This control board regulates all oven functions including timers and cooking modes.

This panel skin is the replacement outer surface for the appliance control console, restoring the console's finished appearance and protecting buttons and trim from wear. It's a direct-fit cosmetic and protective overlay. What it does:

• Covers and protects the control area from scratches, stains, and everyday wear
• Restores faded, peeling, or cracked console surfaces for improved appearance
• Helps prevent dirt and moisture from reaching internal switches and electronics
• Returns the console to its intended look after removal or damage during repair

• Disconnect power to the appliance before starting any repair
• Removal/replacement typically requires removing the console or trim—retain all screws and mounting hardware
• Handle edges carefully to avoid damaging the new skin or surrounding trim
• If clips or adhesive are present, they are intact or replace as needed for secure installation

Fix an unresponsive oven display or touchpad with this control panel. Restores your ability to select cooking modes and view settings on your wall oven.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This foam seal fits between mating parts to create a tight barrier that helps prevent leaks and rattling. Replacing a worn or missing seal restores proper sealing and helps keep your appliance running quietly. What it does:

• Creates a compliant gasket between components to limit air or moisture passage
• Helps dampen vibration and reduce rattling/buzzing where parts meet
• Helps maintain proper airflow or fluid routing as designed
• Typical symptoms include leaks, condensation/frost near a joint, or new vibration noises

• One foam seal

• Disconnect power; turn off the water supply before service
• Note the original seal's routing/orientation before removal
• Clean and dry all mating surfaces; remove old foam and residue
• Install without stretching or over-compressing; ensure even contact with no gaps

This replacement wire harness assembly restores secure electrical connections between controls and components to help your appliance operate safely and reliably. Use it when wiring is damaged, corroded, or has loose connectors. What it does:

• Routes and connects power and signal wires between controls, sensors, and components
• Restores reliable electrical contact when original wiring is frayed, burned, or broken
• Helps stop intermittent power, control failures, or components that won't operate due to wiring faults
• Prevents shorting from exposed wires by providing intact insulation and connectors

• One wire harness assembly as pictured

• Disconnect power (unplug or shut off breaker) before attempting any repair
• Take photos or label connectors to ensure correct reassembly
• Route harness away from sharp edges, moving parts, and heat sources; secure with existing clips or ties

This mounting bracket is a replacement support bracket that secures appliance components and keeps assemblies aligned for reliable operation. It restores proper fit and helps prevent rattling or movement from loose fittings. What it does:

• Secures panels or assemblies to the appliance frame to maintain proper alignment
• Reduces vibration and rattling caused by loose or damaged supports
• Restores mounting points that prevent sagging or separation of connected parts
• Helps ensure stable operation after repairs involving removed or replaced hardware

• Follow the appliance service manual for exact location and fastener torque
• Disconnect power (and gas if applicable) before beginning any repair
• Use appropriate tools and replace any damaged screws or clips with OEM-equivalent fasteners

Fix intermittent power or control failures in your electric wall oven. This wire harness assembly restores safe electrical connections between components.