Parts for Frigidaire PCFD3668AFA: Control Panel / Top Burners Parts

This spring restores proper tension to the refrigerator door hinge so the door opens and closes smoothly and stays aligned. It replaces a worn or broken hinge spring to reduce sagging and uneven door movement. What it does

• Provides hinge tension so doors close fully and seal properly
• Helps prevent door sag, misalignment, and uneven gaps
• Reduces grinding or rubbing noises from the hinge area
• Restores expected door operation after a broken or stretched spring

• One replacement hinge spring

• Disconnect power to the appliance before beginning any repair
• Use proper hand tools and keep fingers clear of the spring path; springs can release force suddenly
• Installation may require removing the door or hinge assembly; keep track of fasteners and alignment

This electrical harness is a factory-style wire assembly that replaces a damaged or worn wiring connector group to restore power and signal routing. It reconnects controls and components so the appliance operates reliably. What it does

• Routes power and signal connections between control boards, switches, sensors and components.
• Restores interrupted circuits caused by broken, melted or corroded wires or terminals.
• Common symptom fixes: intermittent or no power to a component, controls not responding, or erratic operation.
• Maintains factory routing and connector fit to reduce stress and short risk when installed correctly.

• One electrical harness / wire assembly as shown.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Compare connectors and wire colors to the old harness to ensure correct replacement before installing.
• Secure harness away from moving parts, heat sources and sharp edges; use existing clips or fasteners.

This wiring harness connects multiple refrigerator electrical components to restore power and signals across controls, lights, fans, and motors. It replaces a damaged or worn harness to help return normal appliance operation. What it does

• Routes power and signal connections between the appliance control and internal components.
• Restores operation when a broken or shorted wire causes lights, fans, or compressor to not run.
• Helps stop intermittent electrical problems caused by frayed, corroded, or disconnected wires.
• Prevents shorts by replacing harnesses with exposed or damaged insulation.

• One assembled electrical wiring harness.

• Disconnect power at the breaker or unplug the appliance before starting any work.
• Verify connector orientation and gently press connectors fully until they click; do not force.
• Route harness away from moving parts and sharp edges; secure with existing clips or fasteners.

This support mounting bracket secures an internal component to the appliance chassis to restore proper alignment and stability. Replacing a worn or damaged support helps stop sagging, rattling, and uneven operation. What it does:

• Holds and stabilizes a panel, assembly, or internal component to the appliance frame
• Prevents movement that can cause vibration noise or misalignment
• Restores correct fit and clearance for adjacent parts
• Can resolve symptoms like looseness, rattling, or components that sag or shift

• Disconnect power and water before beginning any repair
• Remove panels or trim as needed to access the support; keep fasteners organized
• Inspect mating surfaces and replace any damaged fasteners or clips

This electrical harness is a factory-style wiring connector assembly that delivers power and signals between refrigerator components for reliable operation and easy replacement. What it does:

• Routes power and signal connections to components such as fans, lights, valves and control modules
• Replaces damaged or corroded wiring that can cause intermittent failures or component loss of power
• Helps restore circuits that produce symptoms like no interior lights, non-running fans, or erratic component operation
• Uses OEM-style connectors and wire routing to match original installation

• Disconnect power at the appliance breaker or unplug the unit before starting
• Match connectors and routing to the original harness; do not force connectors or pinch wires
• Secure harness away from sharp edges and moving parts; use existing clips or straps

This rotary selector switch controls cycle selection on compatible Frigidaire appliances, restoring reliable cycle changes and control-panel responsiveness. It replaces a worn or damaged selector to help regain normal user input and cycle selection. What it does:

• Changes the control's selected cycle or setting when the dial is turned
• Re-establishes mechanical/electrical contact if the original switch is worn or intermittent
• Resolves symptoms like unresponsive or stuck cycle selection, erratic setting changes, or no-change when turning the dial
• Works as the user-interface input component between the control panel and main control board

• One selector switch (rotary)

• Disconnect power (unplug or shut off breaker) before starting any repair
• Remove control panel or console to access the switch; retain all screws and fasteners for reassembly
• Note wire locations or take a photo before disconnecting terminals to ensure correct reconnection

This mounting bracket secures panels or components in place to restore proper alignment and reduce movement. Use it when an appliance panel, trim, or internal piece is loose or rattling. What it does:

• Provides a stable attachment point for a panel, trim, or internal component
• Prevents vibration and rattling caused by a failed or bent bracket
• Restores proper alignment to doors or access panels that sit unevenly
• Replaces damaged or broken mounting hardware to improve fit and finish

• Disconnect power and/or gas supply before starting work
• Access may require removing an outer panel or trim; keep fasteners organized
• Use basic hand tools; avoid overtightening to prevent stripping or damage

This regulator controls gas pressure to the range/oven's burner system so burners and oven heat reliably. It restores correct fuel flow for consistent flames and cooking performance when the regulator is failing. What it does

• Regulates incoming gas pressure for stable burner and oven flames
• Helps ensure even oven temperatures and consistent burner heat
• Common symptom: burners or oven ignite weakly or fail to maintain flame
• Common symptom: inconsistent cooking or uneven baking

• One regulator

• Turn off gas supply and disconnect power before servicing
• Inspect gas connections and leak-test after installation per local codes
• Do not modify the part; use the exact replacement for safety and proper operation

This holder is a small mounting bracket designed to secure a fridge component in place and restore proper alignment. It keeps parts stable to reduce noise and prevent wear from vibration. What it does:

• Secures the targeted component to the cabinet or assembly so it stays in the correct position
• Prevents rattling, shifting, or misalignment that can occur with a loose or broken holder
• Helps maintain proper operation of the attached part by keeping connections stable
• Common symptom: part moves, vibrates, or produces noise during operation

• One holder/mounting bracket

• Disconnect power to the appliance before beginning any repair
• Refer to the OEM parts diagram for correct orientation and mounting location
• Use appropriate hand tools and replace any damaged fasteners; do not overtighten plastic components
• If the surrounding components are damaged, inspect and replace as needed for secure installation

This is a replacement screw used to secure appliance panels and components so assemblies stay properly mounted and stable. It restores hardware that has become lost, stripped, or damaged. What it does:

• Fastens and secures panels, brackets, or trim pieces to the appliance
• Replaces missing or damaged screws that cause loose or rattling parts
• Helps maintain proper alignment of covers and access panels
• Prevents further wear from unsecured components

• Disconnect power before servicing electrical appliances to avoid shock
• Use the correct driver and size to avoid stripping the head
• Tighten until snug; do not overtighten to prevent damage to threads or plastic parts
• Replace all matching fasteners for even fit