Parts for Jenn-Air JDS9860BCP: 03 - Control Panel / Top Assembly Parts

A replacement SN switch that restores the appliance's control function so selections and features respond reliably. Installs in the original switch location to return consistent on/off or selector operation after a switch failure. What it does:

• Opens and closes the electrical circuit to control the associated function or component.
• Replaces a worn or failed switch to stop intermittent operation or loss of control.
• Common symptoms it can fix: appliance not responding to a selector/setting, intermittent power to a component, or a component that won't turn on.
• Functions as the user-facing or internal control switch depending on the model application.

• Disconnect power (unplug appliance or shut off breaker) before starting any repair.
• May require removing an access or control panel; use basic hand tools and note wire locations before disconnecting.

Color: Black.

This is a black cast iron double burner grate that spans two burners on a gas range cooktop, providing a stable surface for pots and pans. It supports cookware over the flames and allows for even heat distribution. Replace this grate if it is cracked, warped, rusted, or if its feet are worn down, causing cookware to sit unevenly.

Mounting screw secures panels, brackets, and components inside your oven. Replace missing, stripped, or damaged screws to restore proper fit.

This electronic control board with overlay manages your range or wall oven's heating and user interface. Replacing a failing control restores accurate temperature regulation, proper bake/broil operation, and a readable display so the appliance responds as it should.

• Regulates oven heat by switching bake/broil circuits based on temperature sensor feedback
• Powers and displays the clock, timer, and status messages
• Interprets keypad/touchpad inputs to run bake, broil, and clean cycles
• Common failure symptoms: dark or flickering display, unresponsive buttons, oven won't start or maintain set temperature, or error codes

• Disconnect power at the breaker before servicing; verify no voltage present
• Use ESD precautions and handle the board by its edges
• Photograph/label wiring; move connectors one at a time to the new board and seat fully
• After installation, run any model-specific checks or calibrations per the service/tech sheet

This stainless steel control knob fits on the front panel of the range and is used to adjust the flame on a surface burner. It slides onto the gas valve stem and includes printed markings indicating flame settings. Replace this knob if it is broken, discolored, or no longer turns the valve stem smoothly to control the burner.

Color: Black. For biscuit order 98008169. For white order WP98008544.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Locator pin for gas cooktop burner assembly. Replaces broken, missing, or worn pins that position burner components. Essential hardware for proper alignment.

Fastener nut for securing appliance components and panels. Replace if stripped, corroded, or missing to restore proper assembly and stability.

Screw: 8-16 x 3/8 inch.

Exhaust fan won't turn off or stuck on? This rocker switch restores reliable blower control. Simple 5-minute fix—just disconnect wires and snap in new.

Mounting screw secures panels, brackets, and components inside your oven. Replace missing, stripped, or damaged screws to restore proper fit.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal