Parts for Lg DLHC1455V/00: Control Panel & Top Plate Assy Parts

This refrigerator door assembly replaces a damaged or worn exterior door to restore proper sealing, appearance, and access to the fridge compartment. It fits select LG refrigerators and restores normal door operation and insulation. What it does:

• Replaces a cracked, dented, or bent refrigerator door to improve sealing and energy efficiency.
• Restores proper door alignment and latch engagement to prevent warm air leaks and cooling loss.
• Returns the exterior finish and handle mounting surface to like-new condition.
• Helps resolve common symptoms like visible door damage, poor closure, or uneven gaps.

• Disconnect power and empty/remove food and shelves from the door before starting.
• Installation typically requires removing hinge covers and transferring gaskets, handles, and trim as needed.
• Use proper support for the door during removal/installation to avoid injury or damage.

The Dryer Belt is an OEM part for LG dryers. As a component of the dryer's drive system, this belt works with the motor to power the turning drum.

Causes of a bad dryer belt include normal wear and tear from years of rotating the drum. Moisture exposure, stretching over time, or damage from impact can also prematurely wear belts.

Symptoms of a bad dryer belt are:

• The dryer not starting or functioning through cycles
• An abnormal noise coming from the rear of the machine
• Failure of the drum to tumble clothes during drying

This OEM LG part is also compatible with some Kenmore models.
 

This replacement locker hook mounts on the dryer door and engages the cabinet catch and door switch. It keeps the door securely closed so cycles can start and continue without interruption. What it does:

• Attaches to the door and latches into the cabinet catch to secure the door
• Actuates the door switch so the appliance recognizes the door is closed
• Replaces a cracked, bent, or worn hook
• Resolves issues like the door not latching, popping open, or the unit not starting

• 1 locker hook

• Disconnect power; if gas, also shut off the gas supply
• Open the door and remove the mounting screws securing the old hook
• Position the new hook and tighten screws, reusing existing hardware
• Check latch alignment; the door closes securely and the cycle starts

A replacement refrigerator door gasket that restores a tight seal to help maintain proper cooling and energy efficiency. Installs around the door opening to reduce air leaks and help keep food fresher. What it does:

• Forms an airtight seal around the refrigerator door to prevent warm air entry and cold air loss
• Helps maintain consistent internal temperatures for food safety
• Reduces frosting and moisture buildup caused by air leaks
• Can resolve symptoms like excessive energy use, inconsistent cooling, or a door that feels drafty

• Ensure power to the appliance is off before starting; remove any food from the door area
• Clean the gasket seating surface and let it dry fully before installing the new gasket
• Warm the gasket slightly to make it flexible for proper seating, and check for even fit and continuous contact

This lower dishwasher rack assembly replaces a worn or damaged lower rack to restore safe dish loading and smooth rolling. It provides stable support for dishes and helps maintain proper spray coverage for better cleaning. What it does:

• Replaces a bent, cracked, or broken lower rack that prevents proper loading
• Restores wheel movement and rack sliding for easy access to dishes
• Helps keep dishes properly spaced so water can reach all surfaces
• Reduces rattling and misalignment during dishwasher cycles

• Designed for drop-in replacement; match part number before ordering
• Use gloves to avoid sharp sheet-metal edges and basket wires during install
• Remove power (unplug or switch off circuit) before servicing if working near electrical components
• Inspect and replace those parts for best performance

This dispenser assembly replaces the refrigerator door dispenser housing to restore proper dispensing of water and ice and to secure the dispenser controls and chute. It restores correct alignment and helps stop leaks or jams at the door. What it does

• Houses the dispenser controls, chute and actuator for water and ice dispensing
• Directs water and ice from the door to the cup or bin
• Fixes symptoms such as water leaking at the dispenser, jammed or stuck dispenser lever, or loose/ misaligned dispenser components
• Provides a stable mounting point for switches, nozzles and trim around the dispenser opening

• Disconnect power and shut off the water supply before starting
• Handle components carefully to avoid cracking the plastic trim or damaging wiring
• Test dispenser function and check for leaks after reassembly

This replacement drain hose routes waste water from the washer tub to the drain pump or house drain, restoring proper water discharge and helping prevent leaks or standing water after a cycle. What it does:

• Carries used water from the tub to the drain pump or household drain
• Helps prevent leaks when properly secured with clamps
• Commonly replaced when the machine has slow draining, pooling water, or visible hose damage
• Works with original hose clamps and fittings when the correct connections are used

• Disconnect power and turn off water supply before starting any repair
• Remove access panels as needed to reach hose connections; preserve and reuse original clamps if undamaged
• Ensure hose routing and height match original installation to prevent siphoning or drainage issues
• Inspect connecting fittings and replace clamps if corroded; test for leaks after reassembly

This lint filter assembly captures lint and debris from the dryer air stream to help maintain proper airflow and reduce lint buildup in the cabinet and vent path. It's a direct-fit replacement that restores the filter function. What it does:

• Traps lint and fibers from dryer exhaust to help prevent vent clogs and improve airflow
• Helps maintain drying performance by keeping lint out of the blower and cabinet
• Reduces risk of lint escaping into the drum or vent system
• Visible filter media and frame indicate when cleaning or replacement is needed

• One lint filter assembly

• Disconnect power (and gas supply for gas dryers) before starting any service
• Remove and replace the old filter assembly following the dryer's service instructions
• Inspect filter housing and surrounding seals for damage or obstructions; clean as needed
• Test the dryer for normal operation after installation

This is a factory service parts assembly that replaces a worn or damaged assembly to restore normal appliance operation and functionality. Use when an internal assembly is broken, loose, or causing errors. What it does:

• Replaces a complete service assembly to fix component failures inside the appliance
• Stops symptoms like intermittent operation, unusual noises, loose or detached parts, or error codes tied to the assembly
• Restores correct mechanical or electrical connections provided by the original assembly
• Enables continued use without replacing multiple individual components

• Disconnect power (and water, if applicable) before beginning any repair
• Follow the OEM instructions for correct replacement steps
• Handle connectors and ribbon cables carefully to avoid damage

A small flat metal washer used to space or secure fasteners in the washer's internal assemblies. Helps maintain proper part alignment and reliable fastening so components stay secure during operation. What it does

• Provides a flat bearing surface to distribute clamp load from a nut or bolt
• Acts as a spacer to set proper clearance between parts
• Helps reduce loosening and wear at fastener joints
• Commonly replaced when hardware is loose, rattling, or shows visible wear

• Disconnect power and water before servicing the appliance.
• Install with the correct bolt/nut and torque per the service manual; replace any damaged fasteners.

The Door Switch Assembly is an OEM part for LG dryers. It ensures the dryer operates only when the door is securely closed, acting as a safety feature to prevent the dryer from running while the door is open.

Causes of a bad door switch assembly can include regular wear and tear from frequent use, electrical issues such as shorts or faulty connections, or physical damage from forceful door closures or impacts.

Symptoms of a bad door switch assembly include:

• The dryer not starting
• The dryer stopping mid-cycle
• The drum light not turning on or off correctly
• The dryer continuing to run with the door open

This OEM LG part is also compatible with Sears/Kenmore models.

This deodorizer is a replaceable odor-absorbing assembly that helps reduce lingering smells inside your appliance for fresher results. Designed to fit into the factory deodorizer slot and restore the appliance's odor-control function. What it does:

• Absorbs and reduces common food and musty odors that build up inside the appliance
• Helps maintain a fresher interior between cleanings
• Restores the appliance's original deodorizing feature when the installed unit is degraded
• Improves perceived air quality during and after cycles that produce odors

• One deodorizer assembly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access and replace the deodorizer per the manufacturer's service instructions or parts diagram
• Handle the part gently and install in the correct orientation; verify secure fit before restoring power

This adjustable leg assembly raises and levels the appliance to keep it stable and reduce rocking. It provides a simple way to set appliance height for proper door alignment and smooth operation. What it does:

• Supports the appliance and transfers weight to the floor
• Allows height adjustment to level uneven floors
• Helps prevent excessive vibration, rocking, and noise
• Promotes proper door/drawer alignment and seal

• One leg assembly

• Disconnect power and empty the appliance before adjusting or replacing legs
• Raise or support the appliance safely before removing or installing the leg
• Adjust by turning the leg; tighten securely but avoid over-torquing

This coil tension spring provides the restoring force needed for the appliance component it attaches to, helping return levers or assemblies to their proper position. Replaces a worn or broken spring to restore reliable mechanical action. What it does:

• Applies tension to return or hold a moving part in place during normal operation
• Helps stabilize levers, latches, or small linkages that have become loose or saggy
• Commonly replaced when the appliance shows signs of poor return action, slipping, or intermittent engagement

• One coil tension spring

• Disconnect power and follow manufacturer safety instructions before servicing
• Inspect mating hooks, mounts, or retainers for wear and replace if damaged
• Use proper tools and retainers to avoid the spring releasing unexpectedly

This locker assembly is the latch mechanism that secures the washer door and ensures the machine only runs when the door is properly closed. It restores reliable door engagement and helps prevent mid-cycle door openings. What it does:

• Locks the front door during fill and spin cycles so the washer can operate safely
• Detects and holds the door closed to prevent leaks and interruptions
• Commonly replaces a worn or broken latch that won't engage or lets the door pop open
• Can resolve symptoms like a washer that won't start, shows a door-locking error, or stops mid-cycle

• One locker assembly

• Disconnect power and water supply before starting any work
• Follow the washer's service manual for disassembly and reassembly steps
• Handle plastic tabs and electrical connectors carefully to avoid breakage
• Test a short cycle after installation to ensure proper locking and operation

This customized screw secures appliance panels and components for a reliable fit and safe operation. Use it to replace a missing or damaged fastener and restore proper assembly without needing a full component rebuild. What it does:

• Fastens trim, panels, brackets or small internal components to maintain proper alignment
• Restores lost or stripped fasteners that cause rattling, loose parts, or gaps
• Matches OEM fit for secure, vibration-resistant fastening when replaced correctly
• Helps prevent damage from loose components that can affect performance or safety

• Disconnect power and unplug the appliance before starting any work
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to prevent thread or component damage
• Keep removed screws organized to ensure correct reassembly

This motor support bracket secures the appliance motor in place so it runs quietly and stays aligned with the drive components. Replacing a worn or damaged support restores proper motor positioning and reduces noise and vibration. What it does:

• Holds the motor housing steady to prevent excessive movement during operation
• Maintains motor alignment with the drive system to reduce belt/drum wear
• Can help stop rattling, grinding, or intermittent noise caused by a loose motor mount
• Supports stable rotation that helps prevent premature component wear

• One motor support bracket

• Disconnect power before beginning any repair to avoid shock or injury
• Inspect surrounding mounts, fasteners and motor for damage while replacing the bracket
• Reuse OEM fasteners or replace with equivalent hardware and torque to factory specs

The Screw is an OEM part for LG dryers. This screw secures the front panel to the outer housing, ensuring a properly assembled unit.

Causes of a bad screw can include stripping of threads from over-tightening, loss of the screw from repeated access to internal components, or damage such as cracking from dropping or other impact.

Symptoms of a bad front panel screw include:

• Loose, detached, or missing front panel assembly
• Accessibility issues opening or closing the dryer door
• Reduced stability of the overall dryer cabinet structure

This OEM LG part is also compatible with some Kenmore models.

This parts assembly is a factory-style replacement that restores the appliance's original component arrangement for reliable operation. Fits into the existing mounting points to replace a worn or damaged assembly quickly and safely. What it does:

• Replaces a damaged or nonfunctional assembly to restore the related appliance subsystem.
• Helps stop symptoms like intermittent operation, failure to start, or error codes tied to a failed assembly.
• Restores secure mechanical and electrical connections when the original assembly is broken or corroded.
• Maintains compatibility with the appliance's existing wiring and mounting locations.

• Disconnect power (and water supply if applicable) before beginning any repair.
• Handle electrical connectors and wiring carefully to avoid damage; match connectors exactly when reassembling.
• Use basic hand tools; follow appliance service manual steps for access and removal.

This damper assembly controls fresh air flow into the refrigerator compartment to help regulate internal temperatures. Replaces the factory air inlet damper to restore proper airflow between compartments. What it does:

• Opens and closes the fresh air inlet to control air exchange between compartments
• Helps maintain consistent refrigerator temperatures by regulating incoming air
• Common symptoms: uneven cooling, warm refrigerator compartment, or inconsistent temperatures

• One fresh air damper assembly

• Disconnect power before servicing to avoid electrical shock
• Handle the damper gently to avoid bending the flap or damaging the actuator
• Typically installs with a few screws and simple connectors; verify orientation before tightening

This poly-V drive belt transfers power from the motor to rotate the drum. Replace a stretched or broken belt to restore smooth, dependable tumbling or spinning and reduce slippage or noise.

• Drives the drum by linking the motor pulley through the idler/tensioner system
• Maintains traction for consistent rotation during cycles
• When worn or broken, symptoms include: drum won't turn though motor runs, squealing/chirping, burning rubber smell, or visible fraying/cracks
• Restores proper drum movement and reduces strain on the motor

• Disconnect power before servicing; allow the appliance to cool
• Access the belt by removing panels as directed for your model; note routing before removal
• Release tension at the idler, install the new belt with ribs oriented correctly, and route around motor and idler pulleys
• Spin the drum by hand to seat the belt and verify alignment before reassembly and testing

This safety cover assembly shields internal components and helps prevent accidental contact with moving or energized parts, restoring the appliance's built-in safety barrier. It's a direct-fit replacement part designed to return protective coverage. What it does:

• Covers and protects internal wiring, switches, or mechanisms from debris and user contact
• Prevents accidental access to hazardous components during normal operation
• Helps stop lint, moisture, or small objects from reaching sensitive parts
• Can resolve safety-related faults or error codes caused by damaged or missing covers

• Disconnect power (unplug or switch off breaker) before starting any repair
• Use appropriate hand tools; avoid force that can break retaining tabs or clips
• Handle edges carefully to avoid cuts; wear gloves if needed
• After installation, verify panels and covers are secured and run a short test cycle to normal operation

This drain hose cap seals the end of a dishwasher or washer drain hose to prevent leaks and help keep odors and debris from entering the drain line. It restores a snug, secure hose termination for reliable draining. What it does

• Seals the open end of a drain hose to reduce water leaks at the hose termination.
• Helps prevent sewer odors or debris from traveling back through the hose.
• Keeps hose connection clean and reduces risk of clogging at the open end.
• Useful when replacing a damaged or missing hose end cap to maintain proper drainage.

• Disconnect power and turn off water supply before servicing the appliance.
• Remove the old cap and inspect the hose end for damage or buildup; clean as needed.
• Push the cap onto the hose end until fully seated; verify a snug fit and no visible gaps.
• Test by running a short drain cycle and checking for leaks; replace if cap doesn't seal.

This blower cover houses and protects the appliance's blower assembly to maintain proper airflow and keep moving parts shielded. It restores safe airflow pathways and helps prevent debris from contacting the blower wheel. What it does:

• Protects the blower wheel and motor from lint, debris, and accidental contact
• Directs airflow from the blower to the appliance ducting for efficient ventilation
• Helps reduce rattling or rubbing caused by a damaged or missing cover
• Supports correct blower alignment to avoid uneven wear or noise

• Disconnect power before accessing internal components to avoid electrical shock
• Basic hand tools may be needed; handle plastic parts gently to avoid cracking
• Inspect blower wheel and mounting before reassembly and replace any damaged fasteners

This small fastening nut secures components and assemblies on compatible LG appliances, restoring a reliable connection and reducing rattles or loose parts. It's a simple replacement for worn or missing nuts. What it does:

• Fastens panels, brackets, or hardware to keep parts secure
• Prevents vibration-related noise and movement from loose fasteners
• Replaces corroded, stripped, or missing nuts that cause instability
• Works wherever the OEM "Nut, Common" is specified

• Disconnect power or gas and turn off water supply before servicing
• Use the correct wrench or socket to avoid rounding the nut
• Do not overtighten; secure to OEM torque if available
• If threading is damaged, replace the mating bolt/stud as well

This damper regulates airflow between refrigerator compartments to help maintain proper cooling balance. Replaces a failed or stuck damper to restore controlled cold-air movement and improve temperature consistency. What it does:

• Opens and closes to direct cold air between freezer and fresh-food sections
• Helps balance compartment temperatures for better food preservation
• A faulty damper can cause warm fridge compartments, uneven cooling, or excessive freezer run time
• Works with the refrigerator's control system to respond to temperature settings

• Disconnect power to the appliance before beginning work
• Access typically requires removing interior panels or shelving—keep fasteners organized
• Handle the linkage and actuator carefully to avoid bending or damage
• Test operation after installation and restore all panels and shelves