Parts for Ge GUD27EESN0WW: Controls & Backsplash Parts

Secures dryer panels, brackets, and internal assemblies. Replace missing, stripped, or damaged screws to restore proper alignment and prevent vibration.

Mounting screw hardware for ranges and cooktops. Replace missing, stripped, or corroded screws used to secure panels, brackets, or components.

This silicon controlled rectifier (SCR) is an electronic switching device used in appliance control circuitry to regulate power to motors or heating circuits. Replacing a faulty SCR restores reliable power control and helps resolve intermittent or failed operation. What it does:

• Controls and modulates electrical current in control boards and power circuits
• Allows timed or variable power delivery to heating elements or motors in appliances
• Helps stop intermittent operation caused by a failed switching device
• Commonly replaced when an appliance experiences no heat, no motor run, or erratic performance

• Disconnect power to the appliance before servicing to avoid electric shock
• Handle with ESD precautions; avoid touching terminals and static-sensitive areas
• Install the replacement SCR with the same orientation and secure mounting as the original

Fix a laundry center that won't start cycles, respond to buttons, or complete wash programs. This main control board restores electronic functions. Moderate repair.

Secures dryer panels and internal components to the cabinet frame. Replace if screw is stripped, missing, or loose to prevent vibration and rattling.

The CAPACITOR is an OEM part for GE washers. It works along with the motor to efficiently power the agitation and spinning functions. The capacitor stores and releases electrical current as needed to ensure a smooth wash action. 

Symptoms of a bad capacitor include:

• The washer unable to progress beyond the initial agitation cycles  
• Sluggish or struggling movements during washing or spinning
• Buzzing, humming, or crackling noises from electrical components
• Frequent tripping of circuit breakers when operating 

Causes of failure can include drying out of internal components over many years, defects in capacitor plates or wiring, or electrical surges damaging sensitive components.

Replace yours today with this genuine OEM GE part for reliable storage and delivery of current. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Restore responsive button and touch control when your laundry center's control panel is damaged or worn. Direct-fit replacement restores full functionality.

Control knob that mounts on the timer shaft to select drying times and cycles. Replace if cracked, broken, or won't grip the shaft properly. Includes clip.

Control panel knob for selecting wash cycles. Replaces broken, cracked, or stripped knobs. Installs on the front panel—simply pull off the old knob.

This start button assembly is the external pushbutton on the dryer console. It lets you begin a cycle; replacing a broken or missing button restores proper engagement of the start switch and a clean, factory appearance.

• Provides the physical Start control on the console and actuates the underlying switch
• Replaces a button that is cracked, missing, loose, or won't stay in place
• Helps when the dryer won't start because the button can't press the switch
• Restores smooth, reliable button travel and appearance

• Disconnect power; if gas, shut off gas supply before moving the appliance
• Access the console, remove fasteners, release tabs, and remove the old button assembly
• Transfer any small hardware from the original as needed; align and secure the new button
• Reassemble, restore power, and test for proper button movement and start engagement

This control board & chassis is the dryer's electronic control assembly. It manages cycle selection, timing, and key functions. Replacing a failed board can restore responsive controls and consistent operation when the console is dead or erratic.

• Manages cycle selection and timing; coordinates inputs from buttons/selector and sensors
• Sends control signals to run the motor and regulate heating as designed
• Can address a dryer that won't start despite correct power and a closed door
• Helps correct cycles that stop early, won't advance, or show random errors/beeping

• Disconnect power before service; if gas, also shut off the gas supply
• Use anti-static precautions when handling the electronic board
• Photograph/label wire connectors, then transfer wiring and any mounting from the old assembly
• After installation, run diagnostics or a test cycle per your model's service information

Control panel buttons not responding? This console wiring harness restores signal connections between your user interface and main control board.

This 27-inch fuse harness connects the dryer's thermal/fuse circuit and helps restore proper power delivery to the heating system. It provides a direct replacement for a worn or damaged harness to help re-establish safe operation. What it does:

• Carries power to the dryer's thermal cut-off/element circuit so the heater can operate
• Replaces frayed, burned or broken wiring that can cause no-heat or intermittent heating
• Restores secure terminal connections to prevent arcing and poor contact
• Supports troubleshooting for heater-related faults when the heater and thermostats test good

• Disconnect all power before servicing; verify the appliance is de-energized
• Inspect mating terminals and connectors; replace or clean damaged contacts before installation
• Route harness to match original routing and secure with existing clips or fasteners

Dryer buttons not responding or display blank? This control board restores console function. Moderate DIY repair—requires panel removal and wiring.

Fix unresponsive buttons or a blank display on your laundry center washer console. This control board restores cycle selection and command input. DIY repair.

Fix a laundry center that won't start cycles or ignores selector settings with a new washer cycle selector switch. Simple DIY repair in about 30 minutes.

Fix a laundry center that won't change cycles or has a loose selector knob with this cycle selector assembly. Moderate DIY repair in 30-45 minutes.