Parts for Ge ZICP720BSDSS: 02 - Controls & Components Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.

Fixes uneven cooling or warm spots in fresh food section. This compartment fan motor circulates air to maintain consistent temperatures throughout refrigerator.

Freezer light not working? This light socket connects the bulb to power. Common fix for interior lighting issues. Simple installation in most models.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Freezer light not turning on or off? This door light switch activates interior lighting when opened. Moderate DIY repair—press tab, rotate out old switch.

If your refrigerator compartment isn't cooling while the freezer stays cold, the evaporator fan motor likely failed. DIY-friendly repair with video guide.

Secures the evaporator fan shroud to the rear compartment frame. Replace if rusted, cracked, or broken to properly support the fan assembly and alignment.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Rubber grommet that seals and cushions where the evaporator fan motor shaft mounts. Replace if cracked, worn, or missing to eliminate noise and vibration.

Secures the evaporator fan motor to the refrigerator cabinet. Replace if your original bracket is bent, broken, or cracked to restore proper mounting.

Molded insulating shield that fits over the refrigerator's ice maker fill tube. Replaces cracked, missing, or damaged covers to restore proper alignment.

Replacement evaporator cover for your refrigerator. This plastic cover protects the evaporator coil assembly. Order a new one if yours is cracked or broken.

Mounting bracket that secures the damper assembly inside your refrigerator. Replace if cracked, broken, or missing to properly support the damper component.

Molded plastic water collector that directs ice maker water to prevent pooling and leaks. Replace if cracked, broken, or missing to restore drainage.

Plastic plug insert that covers shelf support holes in freezer interior walls. Replaces missing, cracked, or damaged plugs for a clean finish.

Fix loud fan noise and poor cooling with a new evaporator fan blade. Restores airflow across coils. Moderately difficult install in tight freezer space.

Refrigerator not cooling or freezing properly? A faulty evaporator coil prevents proper heat absorption. This repair requires moderate skill and 1-2 hours.

Fix ice buildup and warm fridge temps with a new defrost heater. Melts frost from evaporator coils so cold air circulates properly again.

Replace your refrigerator's freezer light shield to protect the bulb and restore proper illumination. Confirm fit with your model number before ordering.

Guides defrost water into the drain opening to prevent puddling and ice buildup. Replace if cracked, broken, or missing to keep water flowing properly.

The Refrigerator Damper and Gasket Assembly is an OEM replacement part for GE refrigerators. It includes a moving damper plate that regulates airflow through vents, as well as its surrounding sealing gasket.

Symptoms of a bad assembly include:

• Inability to maintain proper internal temperatures
• Frost or condensation buildup inside from restricted airflow
• Odors or flavors transferring between compartments
• Noisy ventilation from a loose damper plate

Causes of a bad assembly can be worn over extended use, cracks forming in the damper component itself, or a degraded gasket failing to seal properly.

This genuine GE replacement is compatible with additional GE refrigerator brands including Hotpoint and RCA.

Secures heater and sensor wiring to the evaporator area in your refrigerator. Replace if cracked, broken, or missing to maintain proper wire routing.

Left-side evaporator baffle directs cold air flow in the freezer compartment. Replaces cracked, broken, or missing baffles to restore proper airflow.

Fixes ice buildup in freezer and warm fresh food compartment. This bimetal defrost thermostat controls heater cycles to prevent frost accumulation.

Fixes ice buildup on evaporator coils and inconsistent cooling. This defrost thermostat monitors coil temperature to control the defrost cycle.

Original Whirlpool light bulb, 40 watt.

Symptoms of needing to replace the light bulb include:

• Dimming or flickering light
• Complete lack of illumination inside the appliance
• Visible signs of damage or burnout on the bulb itself

Causes of a faulty light bulb can include normal burnout over time, electrical issues, or physical damage due to impact or vibrations.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Kenmore, Frigidaire, GE, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore appliances.

Protects and directs fresh food compartment light. Replace if cracked or discolored to restore proper illumination. Verify fit with your model number.

This HMI control assembly is the user interface board that lets you select and display settings on the appliance, restoring responsive controls and proper display feedback for normal operation. What it does:

• Provides the touch/key inputs and display signals for the appliance control system
• Registers user commands (cycle selection, temperature, timers) and sends them to the main control
• Restores missing or unresponsive front-panel controls and display feedback
• Can resolve symptoms like non-responsive buttons, blank or erratic display, or failure to accept user inputs

• Always disconnect power to the appliance before servicing to avoid electrical shock
• Handle the board carefully to avoid static damage; use anti-static precautions if available
• Installation typically requires removing the control panel or trim; retain fasteners and gaskets for reassembly

Collects defrost water under your refrigerator. Replace if cracked, leaking, or missing to prevent water damage and moisture buildup on your floor.

Evaporator drip pan that catches and channels defrost water away from the freezer evaporator. Replace if cracked, damaged, or missing to restore drainage.

This HMI control assembly is the user interface board that lets you select and display settings on the appliance, restoring responsive controls and proper display feedback for normal operation. What it does:

• Provides the touch/key inputs and display signals for the appliance control system
• Registers user commands (cycle selection, temperature, timers) and sends them to the main control
• Restores missing or unresponsive front-panel controls and display feedback
• Can resolve symptoms like non-responsive buttons, blank or erratic display, or failure to accept user inputs

• Always disconnect power to the appliance before servicing to avoid electrical shock
• Handle the board carefully to avoid static damage; use anti-static precautions if available
• Installation typically requires removing the control panel or trim; retain fasteners and gaskets for reassembly

Replaces a cracked or broken drain trap in your refrigerator. Installs on the drain hose at the back of the unit. Use pliers to remove the old trap.