Parts for Kenmore 266.1532412 (2661532412, 266 1532412): Controls Parts

Secures and stabilizes the drum inside your washer cabinet. Replace if cracked, stretched, broken, or missing to restore proper support and control.

This is a replacement 8-32 trilobular hex screw used to fasten appliance panels and components. It restores secure mounting and helps eliminate loose parts or rattling caused by missing or worn fasteners. What it does:

• Secures panels, brackets, or components in place using an 8-32 trilobular thread form
• Helps prevent vibration, rattling, and loose connections when fasteners are missing or stripped
• Designed to match OEM thread style for proper engagement and retention
• Used wherever a small hex-head machine screw is required for assembly

• Use the correct driver/socket to avoid rounding the hex head
• Tighten to snug fit; avoid over-torquing which can strip threads or damage parts
• If replacing a stripped hole, inspect mating threads and consider a thread repair or alternate fastening method
• Disconnect power to the appliance before accessing internal components to reduce risk of shock or injury

Washer stops mid-cycle or won't start? This control board manages cycles and timing. Restores proper operation when the main board fails.

Support board for laundry center units. Provides structural support inside the cabinet. Replace if cracked, broken, or damaged from wear or impact.

A small replacement hose clip that secures flexible appliance hoses to fittings to help prevent leaks and disconnections. Fits commonly used appliance hose connections to restore a secure seal and reliable water flow. What it does:

• Secures a water or drain hose to a barb or fitting to prevent the hose from coming loose
• Helps stop leaks and drips caused by loose or slipping hoses
• Prevents hose movement and rubbing that can lead to wear or abrasion
• Useful when a hose slips off during operation or after maintenance

• Disconnect power and shut off the water supply before servicing the appliance
• Use appropriate hand tools (needle-nose pliers or hose clamp pliers) to open and seat the clip
• Position the clip over the fitting and tighten until the hose is snug and secure; avoid over-tightening
• Replace only with the correct OEM-style clip for a proper fit

Dryer won't power on or trips breaker? Replace the terminal block and ground strap assembly to restore safe electrical connections. Easy DIY repair.

Replacement strain relief bracket that secures the power cord at entry point. Needed when bracket is cracked, broken, or missing to restore safe cord routing.

Size: 8-32 t. Includes 12 screws.

Protective cover for the fuse and terminal block in your laundry center. Replace if cracked, broken, or missing to shield electrical connections.

Control board enclosure cover for laundry centers and washer dryer combos. Replaces cracked, broken, or missing enclosure that protects electronics.

This CCMR 30-amp, 120-volt fuse protects the appliance's electrical circuit by opening when current exceeds safe limits. Replace a blown fuse to restore power to the affected circuit and help prevent damage to internal components.

• Provides overcurrent protection for the circuit specified by the manufacturer
• If the fuse is open, the appliance may be dead, won't start, or certain functions won't operate
• Helps prevent wiring and component damage from shorts or overloads
• Repeated fuse failures indicate an underlying electrical issue requiring diagnosis

• Disconnect power to the appliance before servicing
• Locate the fuse in its holder/block and inspect associated wiring for heat or damage
• Test the old fuse for continuity; replace only with the identical rating specified
• Never bypass or upsize a fuse; correct the root cause of the failure before returning to service

Dryer not heating or shutting off unexpectedly? A faulty fuse holder can disrupt circuit protection. This bracket secures your thermal fuse connection.

If your washer overfills, underfills, or won't advance past fill, this electronic water level pressure switch monitors tub pressure to control fills.

Washer not filling properly or overfilling? This pressure switch harness connects the water level sensor to control board. Moderate 30-minute repair.

Wire harness extension assembly for laundry centers. Replaces damaged, frayed, or broken wiring harness extensions. Essential for safe electrical connections.

Includes 12 screws. Size: 8-18 ab.

Replacement mounting screw for dryer panels, brackets, and components. Needed when screws are missing, stripped, or damaged during repairs or disassembly.