Parts for Electrolux EFMG527UIW0: Controls / Top Panel Parts

The Board Assembly is an OEM replacement part for Frigidaire dryers. This assembly houses the main control board responsible for managing and regulating the various functions of the dryer, such as cycle selection, temperature settings, and timing operations.

Symptoms that may indicate a need to replace the board assembly include:

• The dryer not turning on or failing to respond to user inputs
• Issues with cycle selection or inability to change settings
• Error codes or warning indicators displayed related to control board malfunctions
• Inconsistent or erratic drying performance

Causes of a bad board assembly can include electrical faults, power surges, component failures due to age or overheating, or physical damage from impact or moisture exposure. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryer models.

The Knob Assembly is an OEM replacement part for Frigidaire electric dryers. Including the control knob and internal mechanisms, it allows homeowners to precisely select drying cycles, temperatures and other functions. Reliable operation maximizes fabric care.

Potential causes of failure involve general wear from extended everyday use. Heat cycling may deteriorate plastic components at a quicker pace over many years. Accidental damage is also possible.

Symptoms of a faulty knob assembly include:

• Control knob loose, stuck or missing, impeding selection  
• Desired dryer settings refusing to engage properly
• Flimsy or cracked knobs exposing internal mechanisms
• Misaligned buttons causing confusion or disrupted programs

This knob assembly also is also compatible with Electrolux, Westinghouse and select Kenmore models.

This diffuser directs and evens airflow inside the appliance to promote consistent temperature and efficient operation. Replaces a damaged or broken diffuser to restore proper air distribution and reduce airflow noise. What it does:

• Guides cool or warm air from the blower/vent to improve circulation and temperature consistency
• Helps prevent hot or cold spots by evenly dispersing incoming airflow
• Replaces cracked, warped, or missing diffusers that can cause reduced airflow or noise
• Common symptom fixer: uneven cooling, fluctuating temperatures, or rattling/whistling near the vent

• Disconnect power to the appliance before beginning any repair
• Typically installs at the vent or blower outlet; common fasteners are clips or screws — keep hardware if replacing only the diffuser
• Handle plastic parts gently to avoid cracking; align tabs/slots before fastening

This metal top panel replaces the upper rear control housing on compatible Frigidaire ranges and stoves, restoring a secure mounting surface for controls and improving cabinet fit and appearance. Ideal for repairing bent, rusted, or damaged panels. What it does

• Replaces the upper rear housing that supports control knobs, switches and the backguard area
• Restores proper alignment and spacing between the cooktop and rear controls
• Stops light leaks and relieves stress from warped or bent panels
• Commonly used when the panel is dented, rusted, cracked, or has broken mounting tabs

• One top panel

• Disconnect power (and gas, if applicable) before starting any work
• Handle sharp sheet-metal edges with gloves; panel edges can be sharp
• Remove control knobs, backguard, or trim as required and save screws for reinstallation
• Align mounting tabs and secure with original hardware; test controls after reassembly

This top panel in white restores the oven/stove's upper exterior, improving appearance and protecting internal components from spills and debris. It's a direct-replacement exterior shell piece designed to match original fit and finish. What it does:

• Replaces a cracked, warped, dented, or discolored upper cabinet panel
• Protects control housing and internal components from grease, spills, and dust
• Restores a flush, finished look to the appliance top and backguard area
• Helps maintain proper alignment for control and trim pieces

• Disconnect power to the appliance before beginning any work
• Typical removal requires removing screws and lifting the old panel straight out; keep mounting hardware
• Handle edges carefully to avoid cuts and protect the painted finish during installation

This console assembly is the exterior control panel that houses the user controls and interface for your appliance, restoring a secure mounting surface and functional control access. It helps make buttons, switches, and displays usable again. What it does:

• Provides the outer housing for the appliance control buttons, knobs, and display
• Replaces cracked, melted, or warped control-panel surfaces that interfere with normal operation
• Restores proper alignment and mounting for control components and wiring harnesses
• Helps resolve issues where controls are loose, inaccessible, or physically damaged

• Disconnect power (and gas if applicable) before beginning any repair
• Handle the assembly carefully to avoid damaging the attached switches, display, or wiring
• May require removal of trim, screws, and reconnection of wiring harnesses; retain all mounting hardware

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic