Parts for Ge DCL333EB0CC: 01 - Controls & Top Panel Parts

This Rotary Start Switch is an OEM replacement part for GE dryers It is responsible for initiating the dryer's operation when the user turns the knob to the desired cycle and presses the start button. The rotary start switch is typically located on the control panel of the dryer, where the user interacts with the various settings and functions.
The GE dryer rotary start switch can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This part fixes the following symptoms:

• The dryer not starting or responding when the start button is pressed
• The start button feeling loose or not engaging properly
• The dryer starts intermittently or only when the start button is held down
• The dryer starts but immediately stops once the start button is released
• The start switch becomes unresponsive or difficult to turn
• The dryer not cycling through the different drying modes or settings

8 - 32 x 1/4

The Selector Knob is an OEM part for GE washing machines. This knob is used to choose different wash cycles and settings on the control panel, allowing users to customize their laundry preferences. It is designed to fit securely onto the control shaft and provide smooth operation for selecting various options.

Over time, selector knobs can wear out or become damaged due to frequent use or accidental impacts. Causes of a bad selector knob can include cracked or broken plastic, stripped or worn-out internal components, or a loose fit on the control shaft.

Symptoms of a bad selector knob include:

• Difficulty in turning the knob or selecting settings
• Knob spinning freely without changing settings
• Knob falling off or feeling loose
• Visible cracks or damage on the knob

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This top panel replaces the outer cover above the cooktop control area to restore the appliance's finished appearance and protect internal components from spills and heat. It fits into the appliance's front top assembly for a secure finish. What it does:

• Covers and protects control assemblies and wiring from spills, grease, and heat exposure
• Restores a flush, finished look to the appliance front where the original panel was damaged or corroded
• Helps prevent debris from entering internal components that can cause control issues
• Commonly replaced when the panel is dented, rusted, cracked, or has paint damage

• 1 top panel

• Disconnect power at the breaker or unplug the appliance before starting any work
• Remove control knobs and any trim pieces as required to access mounting screws; handle trim carefully to avoid scratching
• Support the top panel during removal and installation to avoid dropping or bending it

This electromechanical timer controls cycle selection and advances the appliance through timed steps to restore normal cycle sequencing and timing. Replaces a worn or non-advancing control so cycles start and complete properly. What it does:

• Rotates to advance the appliance through timed cycles and routes power to motors, valves, and heaters at the correct intervals
• Restores ability to select and complete cycles when a worn timer fails to advance
• Common symptoms: cycles won't advance, no heat or motor power during some cycles, or selector knob turns without changing cycle
• Works as the main mechanical timing control for sequencing components during operation

• Disconnect power before beginning work; confirm power is off at the breaker or unplug the appliance
• Remove control panel or console trim to access the timer; keep fasteners and switches organized
• Transfer any actuator knobs or clips as needed and secure the new timer in place
• After installation, restore power and verify the appliance cycles through settings and functions correctly

A replacement pan head screw used to fasten appliance panels and components. Its standard #8 coarse thread and 3/8-inch length secure trim, brackets, and small assemblies for stable operation. What it does:

• Fastens panels, brackets, and small parts in household appliances
• Replaces stripped, rusted, or missing #8-18 pan head screws
• Restores secure mounting where vibration or wear caused looseness
• Works with sheet-metal or threaded inserts designed for #8-18 screws

• Disconnect power to the appliance before beginning any repair
• Use the correct #2 Phillips or compatible driver to avoid cam-out
• Thread in straight and tighten until snug; avoid over-tightening to prevent stripping
• Keep small screws away from children and dispose of old fasteners safely