Parts for Kenmore 417.81102003 (41781102003, 417 81102003): Controls / Top Panel Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A small replacement retaining ring that secures internal components to restore proper alignment and reliable operation. Use this OEM-style ring when a worn or broken ring lets parts shift or rattle. What it does

• Holds shafts, trim, or small assemblies in place to prevent movement and rattling
• Helps maintain proper alignment of the associated component
• Can stop intermittent contact or noise caused by a loose part
• Prevents parts from slipping out of position during normal use

• Disconnect power (and water supply if applicable) before beginning any repair
• Access the affected assembly per your model's service instructions or diagram
• Use appropriate pliers or a small driver to remove and install the ring; avoid forcing parts
• Inspect surrounding seals, clips, and fasteners and replace any damaged items

This replacement pipe routes water where needed inside the appliance to restore proper flow and stop leaks. It's a direct-fit service tube for systems that use molded or bent piping to move water. What it does

• Channels water between internal components to enable normal operation
• Helps prevent water leaks and pooling when intact
• Commonly replaced when cracked, split, clogged, or disconnected
• Can resolve symptoms like visible leaks, water on the floor, or components not filling properly

• One replacement pipe

• Recommended for customers comfortable with basic appliance disassembly; refer to your model's service manual or IPL for the exact routing and clip locations
• Disconnect power and water supply before starting repair to avoid shock or flooding
• Inspect mounting clips, grommets, and seals and replace any damaged hardware to ensure a secure, leak-free fit

This electronic control board manages the appliance's timing, cycle selection, and user interface so your unit responds correctly to commands. Replacing a failed board can restore consistent operation and responsive controls. What it does:

• Controls cycle timing, user inputs, and the appliance's core operating logic
• Directs power signals to components based on selected functions
• Common symptoms of failure: unresponsive or flashing display, failure to start cycles, random shutdowns, or error codes
• Can cause intermittent operation or incorrect cycle behavior when defective

• Always disconnect power at the main supply before servicing to avoid electric shock
• Handle the board by its edges and use anti-static precautions to protect electronic components
• The replacement part number and connector locations match the original before installation

This terminal block provides the mounting point and secure electrical connection for the appliance power leads. Replacing a damaged or corroded terminal block restores a solid power connection and reduces arcing or intermittent power. What it does:

• Provides a secure connection between the incoming power cord and the appliance wiring
• Holds and isolates power terminals to prevent shorting and arcing
• Commonly fails when terminals are burned, corroded, loose, or when wires heat at the connection
• Symptoms of a failing terminal include loss of power, intermittent power, visible burn marks or arcing at the connection, and melted or discolored insulation

• One terminal block

• Always disconnect power at the breaker or unplug the appliance before servicing
• Tighten mounting screws and terminal screws securely; inspect and replace any damaged wire insulation

This damper is the refrigerator air-control flap that regulates airflow between compartments to help maintain consistent temperatures and proper cooling. It replaces a worn or stuck damper to restore normal airflow and temperature balance. What it does:

• Opens and closes to direct cold air where needed between freezer and fresh-food sections
• Helps maintain even temperatures and prevents one compartment from getting too warm
• Common symptom: uneven cooling or warm fresh-food section despite running compressor
• Common symptom: damper stuck or not moving, causing poor temperature control

• Disconnect power to the appliance before starting any repair
• Remove interior panels to access the damper; use basic hand tools
• Handle the damper and any wiring harness carefully to avoid damage
• After installation, verify damper operation and allow time for temperatures to stabilize

No.8 pan head `10 - 10b x 0.50 `cr/sq drive