Parts for Ge PS960BL3TS: Cooktop Parts

This maintop glass assembly replaces a cracked, scratched, or burned cooktop surface to restore a clean, even work area and proper support for burners and cookware. It improves appearance and ensures a safe, level cooking surface. What it does:

• Replaces damaged or worn maintop glass to stop heat leaks and prevent debris buildup
• Provides a stable, flat surface for burners, grates, and cookware
• Restores the factory look and helps prevent cuts from cracked glass
• Can stop cooking performance issues caused by warped or broken glass

• One maintop glass assembly

• Disconnect power (and gas, if applicable) before starting any work
• Handle glass carefully; wear gloves and eye protection to avoid injury
• Follow the oven/range service manual for lifting/removing the cooktop and routing wires or clips
• If clips, screws, or gasketing are corroded or broken, replace them per OEM guidance

Burner won't heat or work? This radiant surface element restores your cooktop. Easy DIY fix in about 20 minutes with basic tools. Fits many models.

Burner not heating? This 5.5" radiant element fits beneath glass cooktops. Common fix for non-working burners. Moderate DIY, 20-30 minutes to replace.

This lower oven warming element heats the oven's warming/holding compartment so food stays warm until serving. Replaces a damaged or non-heating lower element to restore consistent low-temperature operation. What it does:

• Heats the oven's warming/lower compartment for holding cooked food
• Replaces elements that show visible damage, burn-through, or no heat output
• Helps restore even low-temperature performance when the warmer function fails
• Works with the oven's temperature control and safety circuits to provide steady heat

• One lower oven warming element

• Disconnect power at the breaker before beginning any repair
• Wear gloves; element edges and terminals may be sharp
• Verify proper wiring and secure terminal connections during installation

Burner element burned out and quit working? This dual radiant surface element restores fast, even heating beneath glass cooktops. 10-15 minute repair.

The Triple Haliant Element is an OEM part for GE cooktops and ranges, designed to provide versatile and powerful heating options. This element features a triple-ring design that allows for three different sizes of cookware to be heated efficiently on the same burner. It's ideal for situations requiring precise temperature control and flexibility, such as when cooking with large pots or pans that need even heat distribution.  

Causes for a Triple Haliant Element to fail can include prolonged use leading to wear and tear, overheating that damages the internal components, or electrical issues such as short circuits. 

Symptoms of a bad Triple Haliant Element include:

• The element does not heat up
• Only parts of the element heat up
• Unusual fluctuations in heat levels

This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 

The Radiant Element Spring is an OEM part for GE electric ranges. This spring supports the radiant element coil and provides the necessary tension to allow the coil to glow red-hot during the cooking process.

Causes of a bad spring can include fatigue from repeated heating and cooling cycles, damage due to impact or mishandling, or corrosion over extended use.

Symptoms of a bad radiant element spring include:

• Radiant element coil sagging or not sitting flush
• Element coil not heating properly or heating unevenly
• Excessive heat and energy use from a misaligned coil
• Element mounting brackets becoming loose over time

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Rear Vent Trim and Gasket Assembly is an OEM part for GE ranges. It seals the rear vent opening of the range, directing hot air and potential gas fumes outside through the exhaust vent during oven use. Without an intact seal provided by the gasket and vent trim, combustion byproducts can enter the kitchen presenting safety and performance issues.

Causes of a bad range rear vent assembly include wear over years of use with high heat cycles, cracking or degradation of sealing materials, or damage from cleaning or impacts around the vent area.

Symptoms of an issue include:

• Foul odors detected in the kitchen during use of the oven
• Inefficient or uneven baking and broiling
• Visible openings or gaps seen around the rear vent perimeter
• Detached, cracked, or missing components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement mounting screw for electric ranges and wall ovens. Secures components and panels. Order a new screw if yours is stripped, missing, or damaged.

Black. 8-18 AB HXW 3/8

Range burner clip secures burner components in place. Replace if bent, broken, or burners wobble. Verify fit with your model number before ordering.