Parts for Ge JT930BH2BB: 07 - Cooling Fan Parts

This right-side fan housing secures the appliance's fan and directs airflow to maintain proper cooling and ventilation. It replaces a damaged or cracked housing to reduce vibration and restore correct fan alignment for quieter operation. What it does:

• Holds the fan motor and blades in the correct position to ensure stable rotation and airflow
• Channels airflow where needed for proper cooling or ventilation inside the appliance
• Helps reduce fan vibration and associated noise when intact and properly mounted
• Prevents contact between the spinning fan and nearby components or wiring

• One right-side fan housing

• Designed for direct replacement; use the manufacturer's fasteners and align mounting tabs before tightening
• Disconnect power to the appliance before beginning work to avoid electrical shock
• Inspect the fan blade and motor for damage while the housing is removed; replace any worn components separately
• If clips or gaskets are present, confirm they are installed and seated per OEM orientation

This left fan cover protects the oven's convection/cooling fan and helps direct airflow for reliable temperature control. It replaces a damaged or missing fan shroud to restore proper airflow and reduce contact with the spinning fan. What it does:

• Shields the fan blade from debris and prevents accidental contact
• Directs airflow for stable oven temperature and efficient cooling
• Reduces fan vibration and related noise when properly seated
• Helps protect the fan motor mounting and wiring from damage

• One left fan cover

• Always disconnect power to the appliance before beginning service
• Remove access panels or oven back as required; retain mounting hardware
• Handle edges carefully — part or surrounding sheet metal may be sharp
• Test fan operation after installation and reassemble panels securely

This fan assy transformer converts and routes power for the appliance fan motor so the cooling/blower fan operates reliably. Replacing a failed transformer restores proper fan function and helps maintain correct internal temperatures. What it does:

• Supplies the correct voltage/current to the fan motor so the blower/cooling fan runs as designed
• Helps prevent fan stalling or intermittent operation caused by a failing transformer
• Can resolve overheating symptoms or poor cooling tied to a non-functional fan circuit
• Works as the electrical interface between the appliance control system and the fan motor

• Always disconnect power to the appliance before inspecting or replacing electrical components
• Handle wiring and connectors carefully; match terminal positions and wire colors during reinstall
• Inspect mounting hardware and grommets; replace any damaged clips or insulation to prevent vibration noise

This rear fan housing cover protects the dryer's blower and rear fan area from lint, debris and accidental contact, helping maintain airflow and safe operation. It's a direct-fit replacement when the original is cracked or missing. What it does:

• Protects the rear fan and blower assembly from lint accumulation and foreign objects
• Helps maintain proper airflow through the dryer cabinet
• Reduces risk of contact with rotating fan components
• Can address symptoms like unusual air leaks from the rear, visible housing damage, or loose/missing rear cover

• One rear fan housing cover

• Disconnect power to the appliance before beginning any repair
• Remove the dryer's back panel or cabinet to access the rear fan housing
• Inspect adjacent components (fan, blower wheel, mounting screws) and replace any damaged fasteners during reassembly

This left-side sail bracket secures the refrigerator dispenser/sail assembly to the freezer door, restoring proper alignment and a solid fit so the dispenser operates smoothly and looks finished. What it does:

• Anchors the left side of the dispenser/sail assembly to the door frame for stable operation
• Prevents sagging, gaps, or misalignment around the dispenser opening
• Helps maintain proper sealing and appearance of the outer door/sail area
• Can resolve dispenser wobble or loose-feeling sash/sail components

• One left-side sail bracket

• Designed to replace the factory left sail bracket; follow your model's service manual for disassembly/reassembly steps
• Inspect adjacent clips and screws; replace any damaged fasteners for a secure fit
• Disconnect power to the appliance before starting work and handle plastic trim carefully to avoid cracking

This is a replacement right switch sail — the right-side actuator that mounts to the appliance control panel and engages the underlying switch. It restores a positive tactile lever so the control switch can be operated reliably. What it does:

• Replaces a broken, cracked or missing right-side switch actuator on the control panel
• Provides a firm, consistent surface to engage the underlying electrical switch
• Helps eliminate loose, stuck, or non-responsive control levers
• Restores correct alignment so the switch clicks and functions as intended

• One right switch sail (actuator) as shown

• High-level swap: remove the control panel trim, lift out the old actuator, and snap the new sail into the switch housing
• Use care to avoid damaging nearby plastic tabs or the switch; verify correct orientation before snapping into place
• Disconnect power to the appliance before starting any repair to avoid electrical shock

This replacement mounting screw is used in cooking appliances to fasten components securely. It restores a tight, rattle-free fit so panels, brackets, or burner-related parts stay properly aligned during everyday use.

• Secures appliance components to the chassis or assembly
• Replaces a missing, stripped, or corroded screw
• Helps resolve loose panels, wobbling parts, or vibration noises
• Supports proper alignment of mounted parts

• Disconnect power at the breaker; for gas units, also shut off gas supply
• Allow the appliance to cool completely before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Tighten snugly without overtightening; replace damaged threads or hardware as needed

This is a replacement screw that can be used with many different types of household appliances. Screws fasten various pieces of machines together. They can also help to reduce the amount of vibration in the machine. If a screw is missing or damaged, it could cause a machine to stop working properly, or to vibrate more than it should.The screws are made from metal and will typically last for a long time. However, the threads and other parts of the screw can wear down with use. The screws could also become lost when making other repairs to the appliance. Replacement of the screws is generally easy, but it will depend on where it is placed.This item can replace certain screws found in various models of ranges, ovens, dryers, and microwaves from General Electric, Hotpoint, Whirlpool, and Kenmore. This is a genuine OEM replacement part sourced from the manufacturer. It is sold individually. Owners may want to have several replacements on hand in case they need them.

Black. 8-18 AB HXW 3/8

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage

A single 6-32 keps nut that secures panels and components by combining a hex nut with a captive lock washer for vibration-resistant fastening. Fits standard 6-32 machine screws to restore proper fastener function and fit. What it does:

• Provides a secure threaded connection for 6-32 screws where a built-in lock washer prevents loosening.
• Commonly used to fasten panels, brackets, and small components prone to vibration.
• Replaces missing, stripped, or damaged nuts causing loose panels, rattling, or misaligned parts.
• Works with standard 6-32 threaded hardware in appliance assemblies.

• One keps nut (6-32).

• Unplug or disconnect power before working on the appliance.
• Hand-start the nut on the screw to avoid cross-threading, then tighten with the appropriate wrench or socket.
• Do not overtighten; stop when snug and the captive washer seats against the surface.
• If threads are damaged, replace the mating screw or repair the threads before installing.