Craftsman Engine Parts

This is a replacement carburetor for Husqvarna string trimmers and is also used on some Craftsman models. It consists of an aluminum body with a bright blue choke and cherry red primer bulb. Engines rely on a mixture of fuel and air for proper operation. In a small engine, the fuel and air mix inside the carburetor. This is achieved with a series of small channels, which release a fine mist of fuel into a vortex of air. When one of these channels gets clogged, it can negatively impact engine performance. Carburetors can often be cleaned with a commercial carburetor cleaning spray, but this is sometimes not sufficient to clean a badly clogged carburetor. In this case, other measures such as hypersonic cleaners can often be effective, but they’re not always worth the cost. The alternative is replacing the entire carburetor, which can be done using this kit. This is an OEM part sourced directly from the manufacturer, and it is sold individually. A heat shield is also included with the kit.

Removes contaminants from engine oil to protect internal parts. Replace regularly to maintain engine performance. Confirm fit with your model number.

Mixes air and fuel for your chainsaw engine. Replace if cracked, damaged, or leaking. Installs on engine, may include primer and fuel lines.

Replacement torsion spring for lawn and garden equipment engines. Creates tension between levers and components. Replace if broken, overstretched, or distorted.

Replacement oil drain plug for outdoor power equipment engines. Installs in the oil pan to seal the drain opening. Replace if stripped, cracked, or leaking.

Replaces a cracked, hardened, or broken primer bulb on gas-powered engines. Installs on the carburetor to inject fuel for priming before starting.

Fuel line kit for small engines. Carries fuel through the machine. Replace if cracked, leaking, or ends don't fit securely even when clamped down.

The carburetor is the part of the chainsaw that mixes air from the intake valve system and gas before the fuel mixture goes to the engine. This ensures that the chainsaw is capable of continuing to run while it is in use. A bad carburetor will cause problems with how the chainsaw runs, and it may stop running during work. If the engine does not start when the tank is full of fresh fuel, test the carburetor. Start by removing the air filter and pouring a teaspoon of fuel onto the carburetor. Then, pull the starter rope to start the engine. If the engine starts but quickly dies, it means that the carburetor will likely need to be replaced. The replacement of the new carburetor is fairly simple. Remove the rear cover on the chainsaw to remove the old carburetor. Once you have removed the old carburetor, you can then install the new carburetor. Replace the cover and test the chainsaw. This is an OEM sourced part that will work with several models of chainsaws from Poulan and Craftsman.

A ball bearing is a common type of rolling-element bearing. It will use balls to keep space between the bearing races and eliminate friction and contact between moving parts. Ball bearings used in lawn and garden equipment ensure that axial loads and radial loads are evenly supported and that there is only a limited amount of rotational friction on the component. It distributes weight evenly, but will undergo constant wear and tear from vibration, heat, and friction and will need replacement regularly. This ball bearing is a genuine OEM part suited to use in Craftsman, Cub Cadet, Ryobi, Troy-Bilt, MTD, Huskee, Yard Machines, Bolens, Mastercut, and Yard-Man equipment. It may be needed for repair work done on a lawnmower, snowblower, tiller, edger, or a log splitter.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

Fuel filter for small engines on snowblowers, tillers, and lawn equipment. Replace annually or if engine runs rough to ensure clean fuel flow. Verify fit with your model number.

Replace your engine's oil fill plug if it's cracked, stripped, or missing. This plug seals the oil fill opening on small engines for snowblowers and tillers.

Fixes snow thrower that won't start or has a broken pull cord. This recoil starter assembly restores manual starting function. Moderate DIY repair.

Snowblower won't start or pulls hard? This recoil starter assembly restores reliable pull-start function. Common repair for worn or broken recoil.

Starter rope won't retract after pulling? This recoil pulley and spring assembly fixes rope retraction issues on mowers and small engines. Direct fit.