Craftsman Range Parts

This OEM part is a power control board. The power control board provides power to the electronic oven control board. If the oven is no longer turning on, or the digital display is no longer visible, this could mean it's time to replace the power control board. Luckily this is a relatively simple process.To begin, make sure to turn off the power to the oven by unplugging it or shutting off the circuit breaker. Then proceed to remove the upper back panel. Once removed locate the power control board and remove the wire harness and wires attached to it. Be sure to take note of the orientation of the wires to place them into the correct terminals on the new board. Attach the wires to the new board and snap the new board back in place. Resecure the back panel and put the oven back in place.This genuine replacement part is sold individually and is compatible with Bosch, Thermador, and Gaggenau ovens.

This surface burner infinite switch sits behind the knob and regulates power to the cooktop/range element. Replacing a failed switch restores accurate heat settings so the burner can turn on, modulate properly, and shut off as expected.

• Regulates on/off cycling of the surface element to achieve the selected heat level
• Sends power to the burner based on knob position
• Common failure symptoms: burner won't heat, only runs on high, won't shut off, or heats erratically
• Knob turns but the burner does not respond

• Disconnect power at the breaker before servicing; surface elements operate at high voltage
• Pull off the knob and remove the control panel/backguard as needed to access the switch
• Transfer wires one at a time from the old switch to the matching terminals on the new switch
• Align the shaft to fit your knob, reassemble the panel, restore power, and test operation

This control display board is the appliance's user-interface module that operates the front control panel and display, giving visible status and responding to user input. Replacing it fixes display and control issues safely and simply. What it does:

• Provides the visible display and interprets button/touch inputs so the appliance responds to selections.
• Can produce unresponsive or intermittent buttons/touch controls and erratic indicator lights.
• May trigger control errors or prevent cycle selection if damaged.

• Disconnect all power before starting — turn off breaker or unplug the appliance.
• Handle the board carefully and avoid static discharge; use a grounding strap if available.
• Remove and reattach wire connectors and mounting hardware gently; note connector orientation.
• Reconnect power and verify functions before reassembling trim or covers.

This infinite switch controls the variable heat settings for a cooktop surface burner, restoring adjustable heating for smooth cooking. It replaces a failed control to help the burner reach and hold selected temperature levels. What it does

• Regulates power to a surface element so heat changes smoothly from low to high.
• Common symptom: burner won't heat or only works on one setting.
• Common symptom: heat level won't change or is stuck at a single setting.
• Can cause clicking or intermittent burner operation when failing.

• Disconnect power to the appliance at the breaker before servicing.
• Confirm terminal locations and wiring match your original switch; label wires before disconnecting.
• Access typically requires removing the cooktop or control panel.

This round cooktop surface element provides a direct heat source for electric ranges, restoring one burner's ability to heat cookware evenly. It's a straightforward replacement for a damaged or non-heating burner element. What it does:

• Heats cookware on an electric range cooktop so pots and pans can reach cooking temperatures
• Replaces a cracked, burned-through, or non-functioning surface element to restore burner operation
• Helps eliminate intermittent or no-heat symptoms on the affected burner
• Works with the range's existing terminal block and controls when compatible

• One cooktop surface (round) element

• Disconnect power to the range at the circuit breaker before starting work
• Remove the damaged element from its terminal connections and lift out; install the new element by seating terminals fully and testing power
• Use care to avoid scratching the cooktop surface and verify element compatibility with your model

The Jet Holder is an OEM part for Bosch ranges. It is responsible for securely housing components that generate flames and distribute heat across the cooktop surface. The jet holder ensures proper airflow and fuel ignition during operation.

Symptoms of a bad jet holder include:

• Unsteady or unstable flames during cooking  
• Flames that cross-ignite between burners
• Inefficient heat transfer causing slow cooking times
• Loose, damaged, or missing jet holder components

Causes of a bad jet holder can include cracks developing from excessive heat cycling or debris buildup restricting gas/airflow. Mineral deposits may also cause fittings to warp and lead to improper alignment. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This gas pressure regulator controls and stabilizes incoming supply pressure to the appliance manifold, helping ensure consistent burner flames and reliable ignition. Replace if the original regulator is sticking or no longer maintaining correct pressure.

• Regulates incoming gas to the appliance's rated manifold pressure
• Helps maintain even flame height and proper combustion
• Supports reliable burner ignition and reduces flame-out from pressure swings
• Common symptoms include weak or uneven flames, yellow tipping, burners not lighting or not staying lit, or flames that are too high

• Disconnect electrical power and shut off the gas supply before servicing
• Observe the flow-direction arrow; install with outlet toward the appliance manifold
• Use approved gas-rated thread sealant on male threads only and leak-test all joints with a non-corrosive solution after installation

This convection ring element supplies the heat for the oven's convection bake and roast cycles. Replacing a failed element restores even convection performance so foods cook properly across multiple racks.

• Provides the heat source for convection modes; the fan circulates air across this ring for uniform baking
• Common symptoms of failure: no heat in convection, very long preheat, or uneven results during convection cycles
• Visual clues include cracks, blistering, or burn-through on the element band
• Electrical clue: element tests open/infinite (OL) with a multimeter when power is disconnected

• Disconnect power at the breaker before servicing; this is a high-wattage circuit
• Access varies by model: remove the rear panel or the interior convection cover to reach the element and terminals
• Note wire locations and transfer leads to the new element one at a time
• Ensure the element sits flat and does not contact the cavity walls; tighten mounting screws snugly

A flexible replacement gasket that seals and side lamp glass, cushioning and securing the glass to help block moisture and debris from the lamp housing. Restores a tighter fit and reduces vibration or rattling around the lamp area. What it does:

• Seals the edge of the lamp glass to keep moisture, dust and food debris out of the lamp housing.
• Cushions and centers the lamp glass to reduce vibration and prevent rattling or glass movement.
• Helps maintain a stable lamp assembly so the light cover sits flush and stays in place.
• Use when the gasket is cracked, torn, deformed or missing, or when the lamp glass feels loose.

• Disconnect power to the appliance before servicing to avoid electrical shock.
• Handle lamp glass carefully to avoid breakage; wear gloves and eye protection as needed.
• Seat the gasket evenly around the lamp glass edge and press into the channel until fully seated; avoid stretching or deforming the seal.
• Replace only with the exact OEM part number to ensure correct fit and sealing.

This 230V, 1500W radiant cooktop element replaces a damaged or non-working surface burner to restore even heating for compatible electric glass-ceramic ranges. Durable design for direct terminal connections on most Bosch-style cooktops. What it does:

• Heats cookware through direct radiant energy for stovetop cooking
• Replaces a cracked, non-heating, or intermittently working surface element
• Helps eliminate uneven cooking or zones that won't reach set temperatures
• Matches OEM electrical rating for safe, consistent performance

• One radiant element (230V, 1500W)

• Disconnect power at the breaker before inspecting or replacing the element
• Allow the cooktop to fully cool; element and glass surface can retain heat
• Verify terminal connections and secure mounting per range instructions

This is an air cleaner collar used on carburetors found in outdoor power equipment. The air cleaner prevents dirt, dust, or debris from entering the engine, preventing serious problems. The air cleaner collar attaches to the carburetor and provides support to the air filter.A new air cleaner collar may be needed if the original is broken, cracked, or damaged in any way. A functional air cleaner collar is vital to keep dirt and debris out of the engine.This part is a genuine Tecumseh part and is an OEM part sourced directly from the manufacturer and it is sold individually. This air cleaner collar is compatible with four-cycle horizontal engines that are manufactured by Tecumseh or Husqvarna.