Craftsman Tiller Carburetor

A carburetor is responsible for combining fuel and air into the right combustible mixture. When it is malfunctioning, there are several warning signs to look out for. These include poor fuel economy, rough idle, flooding, and engine misfire. Installing a brand-new carburetor can help. A carburetor replacement is easy and starts with turning off the lawnmower. Open its air filter cover and use a screwdriver to remove the air filter base. Once detached, disconnect the throttle cable and fuel line. Place the new carburetor and connect the fuel line and the throttle cable. Put back the air filter base. This is a brand-new and original MTD carburetor. It is compatible with tillers, leaf blowers, and string trimmers from MTD, Bolens, Craftsman, Troy-Bilt, Yard-Man, and Yard Machines. This carburetor is fully assembled and sold individually. Additional carburetor gaskets are sold separately.

This carburetor is a device for supplying a two-cycle engine with a mixture of air and fuel. This part comes pre-assembled and has a plastic choke lever along with a metal body. The primary purpose of a carburetor is to mix the right amount of fuel with air so that the engine runs properly. If enough fuel is not mixed with the air, the engine runs lean and can either stop running or gets damaged. On the other hand, if too much fuel is mixed with air, the engine runs rich, and it either floods, runs poorly, runs very smoky, or wastes fuel. The carburetor is in charge of getting the right mixture. If the carburetor is clogged, the engine will not get enough fuel. It may not start or may run rough. The procedure to replace the carburetor is quick and easy, taking only around 15 minutes, but it is recommended to work in a ventilated area. This carburetor works with outdoor power tools like the trimmer, leaf blower, and tiller. It is compatible with specific products from popular brands like Craftsman, MTD, Murray, and Troy-Bilt. It is sold individually and is supplied directly from the original equipment manufacturer.

This Craftsman carburetor is the component that mixes together gas and air before the mixture can reach the engine to power a lawn trimmer. If there isn’t enough fuel in the mix, it can damage the engine or cause the trimmer not to run. Too much fuel can create excess smoke, poor performance, or can prevent the engine from starting. Testing whether a carburetor needs to be replaced can be done by adding a small amount of fuel to the component after removing the air filter. If the engine begins to run but quickly sputters out, this is an indication that the carburetor has a problem. A replacement carburetor can be installed using a wrench, pliers, and safety glasses. This trimmer component is genuine OEM and comes directly from the manufacturer. It is compatible for use with lawn trimmers by Craftsman and MTD. This is an individual item that comes with the carburetor assembly and the carburetor gasket. Pliers and screwdrivers may be needed to complete this replacement or repair.

This is a replacement carburetor assembly that can be used for small engines, such as those found on lawn and garden equipment. The carburetor is where the air and fuel mix before going into the engine. It ensures that there is an accurate ratio of fuel and air, so the engine can start and run efficiently. While carburetors can last a long time, there is always a chance that they will need to be replaced. Normal wear and tear, damage from accidents, chemicals, or corrosion could mean a replacement is necessary. If the owner finds that their engine is sputtering, misfiring, not performing properly, or has trouble starting, the carburetor could have failed. The authentic OEM replacement carburetor features the metal body and the rubber primer bulb. It does not come with gaskets. The carburetor could be used for tillers, trimmers, and edgers. Compatible brands include Cub Cadet, MTD, Yard-Man, and Craftsman. Buyers must make sure they are buying the correct carburetor kit for their engine.

This carburetor assembly can be used as a replacement part for the small engine of a string trimmer, a chainsaw, or an edger. The carburetor assembly contains a replacement carburetor and the components required to facilitate the replacement and installation of the carburetor. The purpose of the carburetor is to create a mixture of the fuel and air that the engine takes in and channel it through the network of valves to the spark plugs, which ignite and power up the engine.A carburetor might have to be replaced if it is damaged to the point of exhibiting the following symptoms, among others: black smoke pluming from the exhaust, reduced fuel economy, misfires and false starts of the engine, and oil leakages stemming directly from the carburetor. If this is the case, this carburetor assembly should be ordered as a replacement. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, MTD. It is sold individually. This carburetor assembly is compatible with the following brands: MTD, Troy-Bilt, Ryobi, and Yard Man.

This is a throttle link made to be used by many types of lawn and garden equipment. It is a metal part that connects the carburetor to the throttle controls. If the throttle link is damaged or broken, it will not be possible to change the speed of the tool's engine. In some cases, if the throttle link is malfunctioning or broken, the equipment may not run at all.The throttle link is made of durable materials but it can be weakened by continued use due to stress and vibrations. This can cause the link to break down and stop working. If this occurs, it will need to be replaced. A screwdriver or an Allen wrench will be required to handle the replacement process. The throttle link will need to be removed from the throttle body so the replacement part can be installed.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The throttle link is created for use with snowblowers, lawnmowers, tillers, pressure washers, and generators made by Briggs & Stratton, Tecumseh, Cub Cadet, Craftsman, MTD, Simplicity, and Toro.

This carburetor nzle fits lawnmowers, lawn tractors, tillers, and other lawn and garden equipment. It is the part of the carburetor assembly that guides the fuel inside of the carburetor and maintains the proper fuel to air ratio. This is an essential part of engine performance. If the carburetor nzle is clogged, damaged, or broken, the engine will not run properly. The carburetor nzle can be replaced as a single repair or as part of an overall carburetor rebuild. Remove the carburetor float and float ring to get to the bowl. Remove the carburetor nzle from inside the carburetor throat with long nose pliers or by pressing it out manually. Ensure both o-rings come out with the nzle; if not, fish them out of the carburetor bowl. Install the o-rings on the new carburetor nzle before installation. This repair should be done in an area with adequate ventilation. Be sure to drain the fuel tank before removing the carburetor and take the spark plug off the engine.This carburetor nzle is sold as an individual unit. It is designed for lawn and garden equipment engines manufactured by Craftsman, Tecumseh, Cub Cadet, Lawn-Boy, and Toro.

The primary function of a carburetor is to mix fuel and air in the right ratio. Fuel enters the carburetor through the fuel inlet fitting and then to the float bowl which delivers fuel to the other circuits. From there, the fuel goes to the needle valve, which is actuated by the float. When there is insufficient fuel, the float will stay down, keeping the valve open. Once the chamber has enough fuel, the float will go up and close the valve. A failed float bowl may leak or have too many dirt particles deposits that impede fuel flow. Luckily, you can easily replace a busted float bowl. This part is a genuine OEM Tecumseh 631867 float bowl replacement. You’ll have the assurance that this replacement is manufactured according to Tecumseh’s highest standards. It is compatible with mowers, tractors, and snowblowers from Toro, Cub Cadet, Lawn-Boy, MTD, and Tecumseh. This part is sold individually.

The float shaft and pin are a genuine replacement for select Tecumseh carburetors on small lawn and garden equipment engines. The float shaft and pin are responsible for maintaining the fuel level within the carburetor. Over time because of repetitive motion, the float pin and shaft can break or become damaged, which will stop the carburetor from functioning properly. If the carburetor cannot function, the engine will not be able to perform. If left unattended, the engine and carburetor could fail completely or bigger issues could occur. Replacing the float is essential to getting the equipment back in order. This genuine float shaft and pin is designed for use on machines from Tecumseh, Poulan, Husqvarna, Lawn Boy, Cub Cadet, MTD, and Craftsman, and is compatible with a number of models. The fuel system should be drained and the engine should be cool before any engine repairs are started. Always wear gloves for hand protection. This float shaft and pin are made of durable materials and sold as a unit. No additional hardware or parts are included.

Carburetors must have tight seals to prevent too much air from getting into the carburetor at one time. If there are issues with a welch plug, it could cause an engine to lose power or to run rough. The plug might have lost its seal, it could have cracked, or it could have become lost. Sometimes, the vibration of the engine is enough to cause a plug to fall out if it is not tightly sealed. A loose fit will cause problems with the flow of fuel. This genuine OEM welch plug is sold individually and can help to seal your carburetor so your engine retains power. The part can be used with a range of lawn tractors, lawnmowers, snowblowers, and small engines. Compatible brands include Tecumseh, Lawn-Boy, Toro, Craftsman, and MTD.

This is a genuine OEM carburetor sourced directly from the manufacturer designed for use in tillers and other small engines. The carburetor controls the mixture and gas and air that reaches the engine at different speeds. Regular use for prolonged periods can lead to the carburetor's failure, resulting in a sluggish engine and reduced fuel economy. A buildup of debris in the carburetor can also cause failure due to clogged airways preventing fuel from reaching the engine. Replacing the carburetor will solve these problems and is much less costly than buying entirely new equipment. Replacing the carburetor requires less than hour of work and a screwdriver, socket or wrench set, and clean basin. Remove the spark plug from the engine and drain the fuel into the clean basin. Locate the air filter and remove it. Remove the fuel line and crankcase. Remove the carburetor from the engine. Install the new carburetor. Reinstall the parts in reverse order. Start the engine and test the carburetor. This is a carburetor made of heavy-duty metal and molded plastic parts; it is sold as an individual pre-assembled unit. The carburetor is compatible with tillers and other small engines manufactured by Toro, Tecumseh, Cub Cadet, and Craftsman.

This is a main nozzle tube replacement for use with a range of different types of outdoor equipment and small engines. Another name for the main nozzle tube is the fuel jet. The fuel will turn into a vapor and then travel through the main nozzle in a vacuum process. This draws the air into the Venturi pipe. The main nozzle tube is made from plastic, and it can eventually start to break down and wear away. When this happens, it will no longer be efficient. Owners might find that the engine is not running smoothly, or that it is difficult to start the engine. Replacing this element of the system could be what is needed. This is a genuine OEM main nozzle tube replacement. It is sold individually and works for various models of lawn mower, snowblower, tiller, pressure washer, generator, log splitter, wood chipper, and other small engines. Compatible brands include MTD, Toro, Cub Cadet, Lawn-Boy, Craftsman, and Briggs & Stratton. Owners should always ensure they are getting the correct replacement for their make and model.