Craftsman Carburetor

A carburetor is responsible for combining fuel and air into the right combustible mixture. When it is malfunctioning, there are several warning signs to look out for. These include poor fuel economy, rough idle, flooding, and engine misfire. Installing a brand-new carburetor can help. A carburetor replacement is easy and starts with turning off the lawnmower. Open its air filter cover and use a screwdriver to remove the air filter base. Once detached, disconnect the throttle cable and fuel line. Place the new carburetor and connect the fuel line and the throttle cable. Put back the air filter base. This is a brand-new and original MTD carburetor. It is compatible with tillers, leaf blowers, and string trimmers from MTD, Bolens, Craftsman, Troy-Bilt, Yard-Man, and Yard Machines. This carburetor is fully assembled and sold individually. Additional carburetor gaskets are sold separately.

This carburetor is a device for supplying a two-cycle engine with a mixture of air and fuel. This part comes pre-assembled and has a plastic choke lever along with a metal body. The primary purpose of a carburetor is to mix the right amount of fuel with air so that the engine runs properly. If enough fuel is not mixed with the air, the engine runs lean and can either stop running or gets damaged. On the other hand, if too much fuel is mixed with air, the engine runs rich, and it either floods, runs poorly, runs very smoky, or wastes fuel. The carburetor is in charge of getting the right mixture. If the carburetor is clogged, the engine will not get enough fuel. It may not start or may run rough. The procedure to replace the carburetor is quick and easy, taking only around 15 minutes, but it is recommended to work in a ventilated area. This carburetor works with outdoor power tools like the trimmer, leaf blower, and tiller. It is compatible with specific products from popular brands like Craftsman, MTD, Murray, and Troy-Bilt. It is sold individually and is supplied directly from the original equipment manufacturer.

This carburetor assembly can be used as a replacement part for the small engine of a string trimmer, a chainsaw, or an edger. The carburetor assembly contains a replacement carburetor and the components required to facilitate the replacement and installation of the carburetor. The purpose of the carburetor is to create a mixture of the fuel and air that the engine takes in and channel it through the network of valves to the spark plugs, which ignite and power up the engine.A carburetor might have to be replaced if it is damaged to the point of exhibiting the following symptoms, among others: black smoke pluming from the exhaust, reduced fuel economy, misfires and false starts of the engine, and oil leakages stemming directly from the carburetor. If this is the case, this carburetor assembly should be ordered as a replacement. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer, MTD. It is sold individually. This carburetor assembly is compatible with the following brands: MTD, Troy-Bilt, Ryobi, and Yard Man.

This Craftsman carburetor is the component that mixes together gas and air before the mixture can reach the engine to power a lawn trimmer. If there isn’t enough fuel in the mix, it can damage the engine or cause the trimmer not to run. Too much fuel can create excess smoke, poor performance, or can prevent the engine from starting. Testing whether a carburetor needs to be replaced can be done by adding a small amount of fuel to the component after removing the air filter. If the engine begins to run but quickly sputters out, this is an indication that the carburetor has a problem. A replacement carburetor can be installed using a wrench, pliers, and safety glasses. This trimmer component is genuine OEM and comes directly from the manufacturer. It is compatible for use with lawn trimmers by Craftsman and MTD. This is an individual item that comes with the carburetor assembly and the carburetor gasket. Pliers and screwdrivers may be needed to complete this replacement or repair.

This carburetor is designed for use with string trimmers. It comes with the full carburetor assembly. This part is used to create the perfect mixture of air and fuel before it is transported into the engine's combustion chamber. The carburetor is made of durable metal. If there is an issue with the carburetor, it may prevent the engine from starting even when the fuel tank is full. Sometimes the carburetor can also be clogged with dirt and debris.Before replacing the carburetor, it should be tested to be sure it is the problem. When the engine doesn't start but fuel is available, move to testing the component. The first step is to remove the air filter from the string trimmer. Add a teaspoon or so of fuel to the carburetor itself and try to start it. If it begins to run but quickly dies, the carburetor is likely the problem and will need to be replaced.This carburetor is a genuine OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual part. The carburetor is made to be compatible with string trimmers manufactured by Cub Cadet and MTD.

This carburetor is a genuine MTD part. A carburetor is a tube that filters the air and fuel through the valves of the engine. This carburetor works with small engine devices such as snowblowers and lawn mowers. Natural wear and tear from the usage of an engine over a long period of time can cause the individual components within the engine to malfunction or fall into disrepair. The longer that a carburetor is in use without replacement, the more likely it is to become damaged or weakened, which will require a swift replacement. Signs of weakening infrastructure for which the carburetor might be responsible can include an engine that frequently stalls or will not start, a clotted fuel bowl blocked by dirt and gunk that results in overflowing fuel through the engine's vents, a poor ratio of air and fuel that results in wheezing, hissing, or popping engine noises, or a poor ratio of air and fuel that results in black smoke pouring out of the engine. Any of these symptoms in an engine will require the immediate replacement of the carburetor.

This carburetor assembly is a genuine MTD part, sold individually. This carburetor assembly can be used as a replacement part in a variety of outdoor appliances including lawn mowers, string trimmers, and edgers. The purpose of a carburetor assembly for one of these outdoor appliances is to prepare a mixture of fuel and air in the proper ratio so that the mixture can be fed into the spark plugs to ignite them and to power on the engine as a result. If the engine is not starting, is hard starting, or if the spark plugs are not igniting properly, the carburetor may be damaged and will require replacement.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This carburetor assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Toro, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Huskee, Bolens, Yard Man, and MasterCut.

This replacement part is a carburetor kit. This is a genuine replacement part made by MTD. This kit is used in many types of machinery and works to ensure that the engine is running properly during use.A new carburetor kit might be needed if the current one is damaged is misplaced at all. This can be due to a single incident or from normal wear and tear. If the engine is struggling to start, it can be due to a faulty carburetor kit. Be sure the engine is completely turned off before attempting to replace this part. Work gloves are also recommended when working near or around the engine. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This carburetor is a genuine MTD part, sold individually. This carburetor can be used as a replacement part in a chainsaw. The purpose of a carburetor in a chainsaw is to filter the mixture of air and fuel so that the two are combined in the proper ratio required to ignite the spark plugs and, in turn, power the appliance.If the engine is hard starting, demonstrating unusual noises such as clicking, crackling, or buzzing, or the engine will not start at all, it is likely that the carburetor has suffered some form of damage and will need to be removed and replaced by this genuine OEM replacement part in order to guarantee safe use of the appliance. Always unplug the appliance before performing any kind of repair or replacement.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This carburetor is compatible with the following outdoor appliance brands: MTD and Craftsman.

This is a replacement carburetor for Husqvarna string trimmers and is also used on some Craftsman models. It consists of an aluminum body with a bright blue choke and cherry red primer bulb. Engines rely on a mixture of fuel and air for proper operation. In a small engine, the fuel and air mix inside the carburetor. This is achieved with a series of small channels, which release a fine mist of fuel into a vortex of air. When one of these channels gets clogged, it can negatively impact engine performance. Carburetors can often be cleaned with a commercial carburetor cleaning spray, but this is sometimes not sufficient to clean a badly clogged carburetor. In this case, other measures such as hypersonic cleaners can often be effective, but they’re not always worth the cost. The alternative is replacing the entire carburetor, which can be done using this kit. This is an OEM part sourced directly from the manufacturer, and it is sold individually. A heat shield is also included with the kit.

The chainsaw carburetor mixes air and gas before this mixture makes its way to the engine. If this is not working correctly, the engine receives a less efficient gas supply or no gas supply at all. If your chainsaw has a full tank of gas but will not start or stops just after starting, the carburetor may need to be replaced. While carburetors can be cleaned to get them working again, they often need to be replaced if they have become too clogged. Depending on what you can reuse from your old carburetor, you may need to order new gaskets as well to ensure an airtight seal. A screwdriver, a nut driver, and a socket wrench set may be needed to complete this repair. This chainsaw carburetor is sold individually from other parts, but it does include the primer bulb. It is compatible with Craftsman and Poulan chainsaws. This chainsaw carburetor is a genuine OEM part.

This is a replacement carburetor assembly that can be used for small engines, such as those found on lawn and garden equipment. The carburetor is where the air and fuel mix before going into the engine. It ensures that there is an accurate ratio of fuel and air, so the engine can start and run efficiently. While carburetors can last a long time, there is always a chance that they will need to be replaced. Normal wear and tear, damage from accidents, chemicals, or corrosion could mean a replacement is necessary. If the owner finds that their engine is sputtering, misfiring, not performing properly, or has trouble starting, the carburetor could have failed. The authentic OEM replacement carburetor features the metal body and the rubber primer bulb. It does not come with gaskets. The carburetor could be used for tillers, trimmers, and edgers. Compatible brands include Cub Cadet, MTD, Yard-Man, and Craftsman. Buyers must make sure they are buying the correct carburetor kit for their engine.

Known as the primer bulb, this replacement part makes it easy for the engine to start. Responsible for circulating fuel through the carburetor, the purge bulb removes air out of the lines and allows the carb to have a new fuel charge before a start. The bulb may harden and crack over time, so it needs to be replaced to prevent an air leak. This is a genuine OEM part that works on different models of gas chainsaws from AYP, Craftsman, Poulan, and Husqvarna. This component is sold individually and comes with two screws.

Trimmers are found in many shapes and sizes, but they all do the same tough job. That is why so many use gas-powered engines that rely on a carburetor to send a proper blend of air and fuel into the cylinder. If an engine starts and dies, or fails to start even with a fresh tank of fuel, it is likely that a carburetor replacement is needed. This replacement carburetor assembly provides a full carburetor replacement on a more than 40 different hand-held trimmer models made by Craftsman or Husqvarna. This is an OEM replacement part that uses durable metal for the body and ships individually. It requires an Allen wrench, pliers and a screwdriver to do the installation.