Parts for Craftsman 358740160: Cylinder Parts

This product is the chainsaw's engine cylinder, which holds fuel ignited by the spark plug. It fits into the existing chamber and houses the pistons during use. It is attached to the carburetor for fuel injection. The spark plug is set within it to ignite the fuel. This part has to be screwed securely into place prior to use and requires lubrication for the engine to run smoothly. If the engine suffers from poor fuel ignition, or leaking fuel, the cylinder may be cracked. When installing the new part, a few holes may require a tap to fit each specific machine. Pistons and bolts sold separately. Existing parts should be cleaned prior to use. This OEM replacement part is sourced straight from the manufacturer and works with certain models of Poulan and Husqvarna small engines.

This replacement part is a transmission insert and is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This transmission insert is used in chainsaws and allows the transmission to operate smoothly. A new transmission insert might be needed if the current one is damaged or missing. If there are noises coming from the inside or the appliance won't stop or start properly, it might be due to a bad transmission insert. Be sure the engine is completely turned off before attempting to start this repair. Because this part is close to other areas that can be dangerous, it is recommended that the user wear work gloves during the job to prevent injury. This transmission insert is a genuine OEM replacement part and is sourced directly from the manufacturer to ensure proper fit. This part is sold individually.

This replacement part is an insert transfer and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Insert transfers are small but very important to many different appliances like chainsaws. These parts reduce friction inside of the motor and piston. Without this part the engine could become damaged.A new insert transfer might be needed if the user hears noises coming from the equipment that are not normal. If there is excess heat coming from inside the appliance this might also be the cause. It is common that insert transfers become stripped overtime due to normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

This muffler bolt is an OEM replacement part that is sourced directly from the manufacturer. These bolts secure the muffler cover to the muffler on chainsaws, trimmers, and other small engines found in lawn and garden machines. Regular use can cause the bolts to loosen and possibly fall out of the cover. The muffler cover requires two bolts to secure it. These bolts have a hexagon-shaped head and require a hex key or Allen wrench to install or remove them from the cover.The muffler on small engines softens the noise coming from the machine. Being exposed to loud noise for long periods can lead to hearing damage. The muffler helps lessen this risk. The muffler cover protects the inner parts of the muffler. Rain, snow, dirt, and debris can cause rust and corrosion. Use the Allen key or hex wrench to loosen the muffler bolt if it is rusted or bent. Install the new bolt and tighten it using the hex wrench. The muffler bolt is made of high-quality steel and it sold as an individual part. The muffler cover requires two bolts to secure the cover. This bolt is compatible with chainsaws, hedge trimmers, and other small engines manufactured by Poulan, Weed Eater, and Husqvarna.

Combustion engines operate because of the chambers that seal in the tiny explosions caused by fuel, air and a spark. The pistons are part of the process of taking power from those explosions, and the piston rings seal the combustion chamber so that all of the gases created remain inside of the engine's crankcase. This replacement piston ring will ensure that a chainsaw's engine can do that, as well as maintaining the right amount of oil between the piston and the cylinder wall. An OEM replacement part, this piston ring works with Craftsman and Husqvarna chainsaws, among others. It will require a wrench set, screwdriver and a pair of pliers to make the replacement. Sold individually.

This ball bearing and seal are used in a range of chainsaw models. It acts as part of the blade assembly and is designed to both lessen friction and stabilize moving parts. This bearing is also set within a race and the entire race/bearing/seal assembly must be replaced at the same time. The bearing is encased with a rubber seal, which prevents fuel leakage and keeps the engine working smoothly. It does not impede the bearing as it turns. Ball bearings are placed in high contact areas and wear down due to friction. They need to be regularly replaced for optimal performance. If the engine shows difficulty while running, or is louder than usual, the seal or bearing may have worn down. This OEM replacement part is sourced from the manufacturer and works with certain models of Poulan small engines, including the Poulan/Poulan Pro 2900, and Husqvarna chainsaws. This part replaces parts 530019259 and 530047827, both of which are obsolete.

This screw is designed to be used in many different chainsaws to connect and hold together various components. The screw can be used on its own or placed with a nut in a pre-drilled and threaded hole. If a nut is going to be used, it is best to choose one with the same threading and finish as the screw that will be used. A screw can become damaged in many ways that will require a replacement. Corrosion, excessive stress, or high temperatures may weaken the screw. In some cases, the damage can cause it to break or become loose and no longer properly secure other components of the chainsaw. A visual inspection can help determine if corrosion is present or the screw is damaged or broken. If the screw is stripped, a bolt remover may be needed to remove it to make the replacement.This screw is a genuine OEM replacement part provided directly from the manufacturer. It is sold as an individual component. The screw is compatible with chainsaws created by Poulan, Poulan Pro, Craftsman, and Husqvarna. A screwdriver is needed to replace, remove, or install the replacement part.