Dacor Refrigerator Parts

Refrigerator door gasket seals the perimeter to keep cold air in and warm air out. Replace if worn, brittle, or loose. Confirm fit with your model.

Creates an airtight seal to keep cold air in and moisture out. Replace when worn or torn to restore cooling performance and prevent frost buildup.

Internal tubing that carries water from the supply valve to various refrigerator components like ice makers and dispensers. Replace if you notice water leaks inside the refrigerator or reduced water flow to dispensers.

Ice not dispensing or spilling in freezer? A cracked or warped ice bucket causes jams and mess. This bin stores ice and positions it for dispensing.

This limit switch monitors a set condition and opens or closes its contacts when that limit is reached. Replacing a failed switch restores proper safety cutoff and consistent operation of the appliance's heating or movement system. What it does:

• Senses a limit condition at its mounting point (such as temperature or travel/position, depending on model)
• Changes state at a defined threshold to protect components and wiring
• Interrupts power to heat or motor circuits, or signals a control to respond
• Common failure signs: no heat or shuts down early, runs continuously, won't start, or intermittent operation

• 1 limit switch

• Disconnect power to the appliance before servicing
• Note wire positions; transfer connectors one at a time or take a photo for reference
• Reinstall in the original orientation so the actuator or sensing surface contacts the correct area
• Address root causes (blocked airflow, binding mechanisms, shorted components) to prevent repeat failures

Replace your freezer door gasket if damaged or causing temperature issues, frost buildup, or visible wear. Ensures proper seal. Verify fit with model.

Fix a refrigerator that won't cool, clicks repeatedly, or has a blank display by replacing the main electronic control board. Moderately difficult repair.

This electronic control board manages key refrigerator functions including compressor operation, defrost cycles, and temperature regulation. It receives input from sensors and user controls to maintain proper cooling in both the fresh food and freezer compartments. Replace this board if the refrigerator is not cooling, displays error codes, runs continuously, or exhibits erratic temperature behavior.

Factory-style replacement screw for securing appliance components. Restores a tight, rattle-free fit for brackets, panels, trims, or covers when the original hardware is missing, stripped, or corroded, helping keep assemblies aligned and secure.

• Fastens components to keep panels, brackets, and trim firmly in place
• Replaces missing, stripped, or rusted hardware that can cause looseness or rattling
• Helps restore proper alignment of parts that won't stay secured
• Useful after service when original fasteners are damaged or lost

• Disconnect power before servicing; shut off water supply if applicable
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten to prevent stripping or cracking adjoining parts

Fix clicking noise, poor cooling, or overheating compressor by replacing a cracked or warped condenser fan blade. Restores airflow across the coil.

This hex washer-head screw secures panels, brackets, and other components inside your appliance. Replacing a worn, stripped, or missing screw restores a tight fit, reduces vibration and rattles, and helps keep assemblies properly aligned.

• Fastens panels, brackets, covers, and internal hardware to the cabinet or frame
• Helps prevent loosening, rattling, or misalignment during appliance operation
• Replace if the head is rounded, threads are stripped, or the screw is missing
• Useful after service when an original fastener is lost or damaged

• Disconnect power and shut off gas/water before starting
• Use the correct nut driver or socket for the hex head to avoid rounding
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening

Ice cubes jamming or hanging up in the ice maker? This stripper arm guides cubes off ejector fingers into the bin. Requires removing ice maker to install.

Mounts at the upper corner of the cabinet to support and pivot the refrigerator door. Replace if bent, cracked, or missing to restore door alignment.

Refrigerator not cooling properly? A clogged filter drier prevents proper refrigerant flow. Requires professional installation due to sealed system.

This replacement screw secures specified refrigerator components—such as covers, brackets, and internal panels—so they stay properly mounted. Replace a missing, stripped, or corroded fastener to restore a tight, rattle-free fit and reliable operation.

• Provides the correct fastener for locations identified in your model's parts diagram
• Helps prevent looseness, vibration, and rattling of panels or brackets
• Replace if the head is stripped, threads are worn, or the screw is missing
• Symptoms can include loose parts, gaps, or noises from movement

• Unplug the refrigerator and shut off water if working near the ice maker or dispenser
• Match length and type to the original; follow your model's parts diagram for placement
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Keep track of screw positions; do not mix different screw lengths or styles

Replaces cracked or broken refrigerator light covers. Protects bulb and shields components from moisture. Slides into place with mounting tabs. Verify fit.