Palmer S Spartanburg , SC November 10, 2015 Appliance: Whirlpool Undercounter Dishwasher DU1100XTPQA Blinking pots and pans light Based on feedback found on the internet, I knew it was either the control panel or control board. Ordered both and it turns out I only needed to replace the control panel. Really easy fix. Turned off the power, unscrewed the top 6 screws to open up the control panel. Removed the cover and disconnected the ribbon cable. Took off the latch assembly and control panel by gently pushing in the plastic tabs. Attached the new control panel by snapping everything back in place, reconnecting the ribbon cable, and putting the cover back on. Screwed everything back in place with the six screws and turn pack on the power. So far, everything is working good as new. Read More... 31 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Megan C Kansas City , KS December 22, 2015 Appliance: Whirlpool Undercounter Dishwasher DU1145XTPQ7 Whirlpool quiet partner ii blinking lights Replaced the control panel because it had short circuited. The Normal, Light and Cancel button were blinking really fast. Found a thread that said it was the control panel. Read More... 5 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Gordon H Jericho , VT October 18, 2017 Appliance: Whirlpool Undercounter Dishwasher DU1055XTVT0 Broken handle on a Whirlpool DU1055xtTVT0 dishwasher. The plastic latch handle on my son & daughter-in-law's dishwasher. While taking off the control panel to look at the problem, I found out that a couple of the post holes in the control panel were broken. If you need to do this, you'll need a small Allen wrench to remove the top 6 screws from the inside of the door and a screwdriver or other tool to help pop some of the plastic clips on the door latch bracket and control board cover. Pull out the control board and disconnect the ribbon cable from it. Connect the ribbon cable on the new control panel to the control board and place the board in the panel and replace the control board cover. Snap the new handle onto the posts on the door latch bracket, and snap the bracket back into the door. Place the control panel in the door, line up the control panel holes with the door holes and replace the screws. I did a web search on the dishwasher model number to find out about parts and found then on AppliancePartsPros.com. The prices there were competitive with other websites and the site had reasonably good reviews. Standard shipping was really quick for me. Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Donna A Valparaiso , IN June 03, 2017 Lights on control panel flashing wouldn't run Ordered new part had a service man replace it. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes
Rollin B Houston , TX February 13, 2024 Appliance: Whirlpool Undercounter Dishwasher DU1100XTPQ6 The older Whirlpool dishwasher would not start washing cycle front panel LED flashing Replaced the exterior control panel. Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Screwdrivers
Trent S Waterford , WI October 19, 2021 Faulty control panel Replaced with a new control panel. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Dennis B Hollywood , FL December 31, 2018 Appliance: Whirlpool Undercounter Dishwasher DU1148XTPQ7 Blinking pots and pans light Tried all the reset button and power interruption suggestions found on the internet. Had a local repairman visit. He got it going but stated it was a temporary fix that wouln't last long and that both the control panel and circuit board would need to be replaced. The "fix" lasted a week. I found this site and learned that only the control panel needed to be replaced. However, I noticed that the suggested replacement part was not identical to mine in that it had only 4 cycle buttons but 5 option buttons while the original part had 5 cycle buttons and 4 option buttons. I tried the site's "chat" feature and got good info but was still uncertain. I called and again got excellent but confusing information. There were two panels available one at about $135 and the other at $153. It was suggested that the $153 panel was the one I needed. However, further investigation on the site stated that the $153 panel was incompatible and that the $135 panel was the correct replacement. I placed the order while on the phone late morning on a Wednesday asking for normal Fed Ex shipping. The part was shipped that afternoon and in my hands about 10:30 Friday morning. There is a You Tube video describing the replacement and saying it takes about 15 minutes. Great video and bang on estimate. Despite having slightly different selections the panel works. Can't be more positive about the service I received from AppliancePartsPros. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Stephen H Gainesville , FL August 19, 2016 Appliance: Whirlpool Undercounter Dishwasher DU1055XTVQ0 Whirlpool quietpartner ii dishwasher stuck in soak & scour mode Soak & Scour LED indicator on the control panel would not shut off. Buttons not working right. Sometimes the control panel would put the dishwasher into other modes as well. Could not simply select a normal wash cycle. I replaced the control panel (not the control board!) which contains the buttons and indicator LEDs. This was an easy fix, requiring only a torx driver of the right size. It took me less than thirty minutes start to finish, most of that time spent looking for my torx driver set. The video says you need to remove the entire front panel of the dishwasher but actually you can just take out the 4-5 screws that hold the control panel and that saves a lot of time. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Kevin B Miami , FL February 16, 2015 Control panel not functional 1) Turned off power at the circuit breaker. 2) Removed the six star screws securing the panel. 3) Gently removed the black cover over the door lever and circuit board. 4) Removed ribbon cable connected to circuit board. 5) Removed control panel. 6) Attached the ribbon cable from the new control panel, to the circuit board. 7) Reseated the circuit board and door lever assembly, then the protective cover. 8) Secured the panel to the door with six star screws. Tightened up everything. 9) Turned power back on at the circuit breaker. 10) Tested the buttons one by one, then ran a normal cycle. Done. Removing the control panel can be a little tricky, unless you have something to rest the panel on, while you try to remove the items listed above. Two people can do this in under 10 minutes. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers