Curt B Woodland , CA April 10, 2016 Appliance: Maytag Washer- Horizontal Axis MAH5500BWW Mah5500bww may tag washer the pause /start button flashed wouldn't come off on off didn't work temp would not resend At first I tried a new control board , didn't work. Than with help and reassurance from appliance prosi tried the controller membrane it works fine 1 1/2 years ago I installed a new seal and new tub bearings. Saved tons by doing the repairs myself. Very satisfied thanks appliance pros. Curt. Woodland ca Read More... 3 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Nut Drivers, Screwdrivers
Scott D Everett , WA April 23, 2014 Appliance: Model MAH550BWW Buttons on console were inop Changed the console, super easy, works like a charm, APP delivered the part in 2 days. Thanks! Read More... 3 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Bill P North Little Rock , AR August 13, 2018 LED console/membrane went bad Replaced console/led membrane. Read More... 1 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers, Socket Set
Kenneth H Albany , NY October 06, 2017 Appliance: Maytag Gas Dryer MDG5500AWW Would not start. Installed new Console. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Pliers, Screwdrivers
William A Lebanon , NJ October 01, 2016 Appliance: Maytag Washer- Horizontal Axis MAH5500BWW Lights on maytag clothes washer console kept reverting to same settings (i e "delicates" "warm warm" Replaced console. Unplugged appliance. Removed back metal panel. Tilted console forward to remove. Removed control board. Disconnected console from control board. Reversed procedure. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Nut Drivers, Screwdrivers
Frank T Owens Cross Roads , AL August 28, 2016 Appliance: Model MAH5500BWWT Not all options functioned Replaced motherboard and control consol Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Tim B Steele , ND February 28, 2016 Appliance: Maytag Washer- Horizontal Axis MAH5500BWW 1 touchpad had mulitple keys sticking 2 belt was wornout 1. Touchpad, remove back and overhead, unhook touchpad wires, remove module and reinstalled module, reinstalled wires and hooked things up. Ran machine through diagnostic test. All was good. 2.Belt: Remove back. Took bolt out of motor. Remove belt. Laid motor on bottom and changed pivot bushings of motor. Remove pulley off back of drum. Remove old belt from behind pulley and cleaned debris. Reinstalled pulley, motor back on drum. Installed bolt in motor before installing belt! Roll new belt in place. Spun multiple revolutions and aligned belt with motor pulley. Run through spin cycle. Installed back on machine. Back in service. Read More... Do-It-Yourself Rating: Repair Time Estimate: 1-2 hours Tools: Nut Drivers, Pliers, Socket Set, Wrench Set
Willie S Longview , TX August 01, 2014 Appliance: Maytag Washer- Horizontal Axis MAH5500BWW I had to hold the start button for up to ten seconds to get the washer to start Replaced the Console Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers
Jamal S Niceville , FL April 24, 2014 Appliance: Model MAH5500BBW Lo error code door will not unlock I noticed a while back that the LED for the door lock was out but I never payed attention to it. My washing machine stopped working and I troubleshot it according to the diagram. Eventually it recommend that i replace the control panel. I ordered a new console thinking that it would come with a new motherboard and to my huge surprise it did not. I was angry! However I removed the old motherboard and put it in the new console...it worked. The entire time the LED light caused my washer to act up because apparently that signal is telling the CPU that everything is OK or not. Unbelievable yet true! I'm glad that I did not immediately return the console when I noticed that it didn't come with a new motherboard. This purchase was great! No issues since. Read More... Do-It-Yourself Rating: Repair Time Estimate: 30-60 minutes Tools: Socket Set
Michael P Cambria , CA April 21, 2014 Appliance: Maytag Washer- Horizontal Axis MAH5500BWW Controls didn't work New console Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers