Parts for Ge ZGP366LR2SS: 06 - Door Assembly Parts

This small set screw secures components inside your refrigerator. Replacing a missing or stripped set screw restores a tight, reliable hold so attached parts stay aligned and are less likely to loosen or rattle during use.

• Fastens an attached part to its mounting point to prevent movement or slipping
• Helps maintain proper alignment of handles, brackets, or trim pieces
• Reduces wobble, vibration, and rattling noises caused by loose hardware
• Replaces missing, stripped, or corroded set screws

• Unplug the refrigerator and shut off water if working near door/dispenser areas
• Support the part being secured; start the screw by hand to avoid cross-threading
• Tighten with the correct driver for your model; do not overtighten to prevent stripping
• The component is secure and aligned before restoring power

Glass bracket for gas ranges. Secures and supports glass components on your range. Replace if cracked, broken, or missing to restore proper fit and stability.

Small end cap that fits the end of a range extension rail or rod to prevent over-travel and provide a finished edge. Replace if cracked, missing, or worn.

Inner oven door liner panel for gas ranges. Installs on the interior side of the oven door. Replace if cracked, warped, discolored, or damaged.

Replacement screw for gas ranges. Secures various components and panels. Needed when original screw is stripped, missing, or damaged during repair work.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Replace cracked, chipped, or broken 27-inch oven door glass. Restores heat-resistant viewing window for monitoring cooking. Direct fit for range door.

Replace your range's broken or damaged oven door handle. This bar-style handle installs on the oven door front for opening and closing access.

This right-side refrigerator door hinge replaces a worn or damaged hinge to restore correct door alignment and smooth opening. It's a direct-fit hinge used where the door is sagging, binding, or not sealing properly. What it does:

• Supports the right-hand door and provides a pivot point for opening and closing
• Restores proper door alignment to improve sealing and temperature consistency
• Reduces binding, scraping or noisy operation caused by a bent or worn hinge
• Helps prevent accelerated wear to the door and cabinet mounting surfaces

• Disconnect power to the appliance and remove stored items from the door before starting.
• Support the door while removing and installing the hinge to prevent damage or injury.
• Use the correct hand tools and tighten fasteners to the manufacturer's torque recommendations.
• If alignment issues persist after installation, check hinge placement and door stops per service instructions.

Left-side door hinge for gas ranges. Secures and guides the oven door for smooth opening and closing. Replace if cracked, broken, or worn out.

Replaces cracked, cloudy, or discolored inner oven door glass. Installs inside the door assembly to restore clear viewing and proper sealing.

Replacement outer glass panel for your gas range oven door. Installs on the door exterior. Order when your glass is cracked, shattered, or broken.

Secures the glass window in your oven door. Replace if the window is loose, rattling, or misaligned. Confirm fit with your model number.

Single fastening screw for range components. Replaces missing, stripped, or damaged screws that secure panels, brackets, and trim pieces in place.

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Seals the gap between your oven door and body to maintain proper cooking temperature. Replace when worn, torn, or heat escapes. Confirm fit with model number.

This is a 1/4-20 x 3/4 inch hex washer head screw used to fasten appliance components securely. It provides a durable, low-profile fastening point to keep panels and assemblies aligned and stable. What it does:

• Secures panels, brackets, and assemblies to prevent movement and maintain alignment
• Helps stop rattling or vibration caused by loose fasteners
• Restores proper fit where a missing or damaged screw causes gaps or instability
• Works with metal-to-metal fastening points requiring 1/4-20 thread engagement

• Disconnect power to the appliance before starting any repair
• Start threads by hand to avoid cross-threading, then tighten with the appropriate hex driver or socket
• Do not overtighten; snug until secure to avoid stripping threads or damaging parts