Parts for Bosch B18IW50NSP/06: Door Assembly Parts

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

A replacement door hinge that restores proper alignment and smooth opening/closing for affected appliance doors. Helps stop sagging, uneven gaps, and dragging doors so the appliance seals and operates more reliably. What it does:

• Supports the door and provides the pivot point for opening and closing
• Restores proper door alignment to correct sagging or uneven gaps
• Reduces binding, rubbing, or noisy operation when the door moves
• Helps the door seat fully to maintain an effective seal

• Disconnect power (and water, if applicable) and remove shelves or panels as needed before starting.
• Support the door while removing or installing the hinge to prevent dropping or damage.
• Use basic hand tools; follow the correct procedure and torque.
• If your model uses matched hinges, consider replacing the pair to maintain even alignment.

This is a mounting fixing kit used to secure specific dishwasher components. It replaces worn or missing hardware so parts stay firmly in place and the appliance operates as intended.

• Secures designated parts to prevent loosening, rattling, or misalignment
• Helps resolve issues like loose panels or components shifting during cycles
• Useful when original fasteners are stripped, corroded, or lost
• Restores proper fitment after service or replacement of related parts

• Disconnect power and turn off water before servicing
• Keep track of original hardware locations for correct reassembly
• Hand-start screws to avoid cross-threading; tighten to snug, do not overtighten
• Address corrosion or damage present on mating parts before installation

This door seal is a molded rubber gasket that helps maintain a tight, reliable seal around the appliance door to prevent leaks and maintain proper performance. Fits the original equipment design and replaces worn or damaged seals. What it does:

• Seals the door perimeter to help prevent water or air leaks during operation
• Restores proper closing pressure and reduces noise from a loose-fitting door
• Helps maintain internal temperature consistency by preventing drafts
• Addresses common symptoms like visible gaps, water pooling, or persistent leaks at the door

• One (1) door seal / door gasket

• Inspect the door/frame mounting channel for debris and clean before installing the new seal
• Press the gasket into the channel evenly, working around the perimeter; ensure full seating without twists
• If adhesive clips or retainer strips are present, reuse only if in good condition or replace as needed
• Disconnect power and water (if applicable) and follow OEM instructions.

This fixture is a small mounting clamp that secures internal components in place to keep them aligned and stable during normal appliance operation. It helps reduce movement and vibration for a quieter, more reliable appliance. What it does:

• Holds internal assemblies or wiring harnesses securely to prevent shifting
• Keeps parts properly positioned to maintain function and reduce wear
• Helps reduce rattling or vibration caused by loose components
• Supports safe, consistent operation by keeping components from contacting other parts

• Disconnect power and water supply before accessing internal components
• Basic hand tools may be required to remove panels and fasten the fixture
• Inspect surrounding clips and fasteners; replace any that are damaged

This fixture is the OEM mounting bracket used to secure internal components inside the appliance, keeping assemblies aligned and stable for reliable operation. It replaces a broken or worn bracket to restore proper fit and reduce movement. What it does

• Secures and positions internal parts to prevent shifting or rattling during operation
• Restores proper alignment of assemblies that rely on the bracket for support
• Can help stop intermittent noises or misfeeds caused by a loose or broken mount
• Protects adjacent components by holding parts in the correct location

• One fixture (mounting bracket) as shown

• Always disconnect power and water before starting repairs
• Typical installation requires basic hand tools; avoid overtightening plastic fasteners
• If damaged surrounding fittings are present, inspect and replace them to ensure a secure fit

This fixture is a small mounting clip designed to secure internal components and panels so they stay correctly positioned during normal appliance operation. It helps reduce movement that can cause noise or misalignment. What it does:

• Secures and positions internal parts or panels to prevent shifting
• Reduces vibration-related noise by holding components firmly
• Helps maintain proper alignment for connected assemblies
• Common symptom: loose or rattling panels or parts that move during operation

• One mounting fixture

• Disconnect power to the appliance before starting any repair
• Use basic hand tools; avoid forcing the clip into place to prevent breakage
• Inspect mating surfaces and replace any damaged mounts or clips
• Test the appliance after installation to ensure the part holds components securely