Parts for Ge JGBS10CEF1CC: 04 - Door & Drawer Parts

Includes 12 speed nuts.

Replace your gas range's broken or worn oven door hinge. This hinge bracket secures the door for smooth opening and closing. Ideal for cracked hinges.

Secures and stabilizes your gas range broiler drawer, allowing smooth sliding and proper alignment. Replace if worn, broken, or missing.

Replace your gas range's broil handle if it's cracked, broken, or missing. This control handle installs on the front panel for broiler operation.

Includes 12 washers.

Spacer that fits between mating parts in your range or oven to maintain proper clearance and alignment. Replace if worn, missing, or damaged to prevent rubbing.

The Bumper is an OEM part for GE ranges. It is located on the sides of the oven drawer and serves as a cushion to prevent noise, vibration, and wear. As time goes on, regular use of the appliance can cause it to become damaged or worn out.

Causes of a bad bumper can include wear and tear from regular use, deterioration of the material over time, or damage from excessive force when closing the door.

Symptoms of a bad Bumper include:

• Excessive noise
• Difficulty in sliding the drawer
• Misalignment
• Wear, and increased friction

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Includes 12 washers.

Replacement mounting screw for electric and gas ranges. Secures internal components and panels. Needed when original screws are stripped, missing, or lost.

Includes 12 screws.

Replacement outer glass panel for range oven doors. Restores clear viewing area when original glass is cracked, broken, or fogged. Bisque color finish.

Color: Bisque

Seals your oven door to retain heat and maintain proper cooking temperature. Replace if torn, brittle, or heat escapes. Clips into place in minutes.

Cushions and secures your range or oven door handle to the door surface. Replace if cracked, worn, or missing to eliminate handle rattling and restore snug fit.

Includes 12 screws.

Insulation pad that lines the oven door to retain heat and reduce exterior temperature. Replace if torn, compressed, or missing for proper efficiency.

Replaces cracked, shattered, or heat-damaged inner glass pane in your range oven door. Restores insulation, visibility, and protects from spills.

Insulation guard that installs inside the oven door assembly to protect internal components. Replace if cracked, torn, or missing during door maintenance.

Insulation panel that installs at the top of your range door to reduce heat transfer and dampen sound. Replace if cracked, deteriorated, or missing.

Replacement mounting screw for range panels, brackets, and trim. Restores secure fit when original fastener is missing, stripped, or damaged.

This mounting screw secures an appliance end cap or trim piece, keeping covers and brackets fastened for safe, stable operation. It's a direct-fit replacement used when the original screw is lost, stripped, or damaged. What it does:

• Secures the end cap or trim to the appliance frame to prevent gaps and movement
• Stops rattling or vibration caused by a missing or worn screw
• Holds covers in place to protect internal components from debris
• Restores proper fit and alignment of the end cap/trim

• Disconnect power before servicing the appliance
• Use the correct screwdriver or bit to avoid stripping the head
• Thread carefully and tighten until snug—do not overtighten
• Replace damaged screws or threaded inserts to ensure a secure fit

Replaces cracked, rusted, or missing bottom trim on your range oven door. This decorative trim piece installs along the lower door edge for a finished look.

Secures the door panel to your range. Replace if the bracket is bent, cracked, or broken, causing the door to sag or misalign during use.

Replace a cracked, broken, or missing end cap on your range door. This decorative trim piece installs at the door edge to complete the finished look.

Replace a cracked or missing end cap on your range door. This plastic trim piece covers the door edge, providing a finished look and protection.

Support bracket for gas range burners. Mounts underneath cooktop to secure burner assembly. Replace if bent, rusted, broken, or missing for proper fit.

Left-hand broiler support plate for gas ranges. Secures the broiler assembly in place. Replace if cracked, warped, or no longer holding components firmly.