Parts for Hot Point RA724K3WH: 03 - Door & Drawer Parts

This oven rack is a replacement wire shelf that supports cookware and bakeware for standard ranges and ovens. It restores proper cooking clearance and helps maintain even heat circulation inside the oven. What it does:

• Provides a stable shelf for pots, pans and baking sheets during cooking or baking.
• Restores correct rack positioning when the original rack is missing, bent, or worn.
• Helps maintain proper airflow and even heat distribution by holding items off the oven floor.
• Fits into existing left/right rack supports and slides into place on oven rack guides.

• Remove power to the appliance before accessing the oven interior for safety.
• Install by sliding the rack into the oven's existing rack guides until fully seated.
• Handle with care; edges can be sharp and the rack will be hot after use.

This broiler pan grid is the oven rack insert that holds food above the broil pan to promote even browning and let drippings fall away. It restores broiling performance for ovens using a two-piece broil pan set. What it does:

• Supports meats and vegetables during broiling so heat circulates around food for better sear and browning
• Allows drippings to fall into the lower broil pan to reduce smoke and flare-ups
• Replaces a missing, warped, or damaged grid that can cause uneven cooking or food slipping through
• Fits into the matching broil pan to restore original broiling configuration

• Ensure oven is off and grid has cooled before handling or installing
• Place grid into the broil pan with grid edges seated securely in the pan
• Clean after use with warm, soapy water; avoid harsh abrasives that can damage the finish

This broil pan is the oven tray designed to catch drippings and hold food while broiling, making cleanup easier and helping food brown under high heat. Fits compatible GE ovens that use this factory broil pan. What it does:

• Holds food close to the broiler element for searing and browning.
• Collects grease and drippings to reduce smoke and make cleanup faster.
• Supports broiling racks or grids (when used with compatible inserts).
• Helps maintain consistent broil performance when the correct pan is in place.

• One broil pan (1 piece)

• Allow the oven to cool and disconnect power before handling or installing parts.
• Slide the pan onto the oven broil supports or into the broiler compartment until seated.
• Use oven mitts when removing after use; clean per manufacturer recommendations.

This genuine replacement screw secures panels, trim and small components on compatible appliances to restore proper fit and prevent rattling or gaps. Use it when a missing or damaged fastener causes loose or misaligned parts. What it does:

• Fastens panels, bezels, trim pieces and small assemblies to the appliance frame
• Restores secure fit to eliminate rattling, vibration noise or loose trim
• Replaces stripped, rusted or missing screws that prevent proper alignment

• Disconnect power to the appliance before servicing to avoid electrical hazard
• Use the correct screwdriver or driver bit to prevent stripping the head
• Tighten securely but avoid over-torquing; excessive force can strip threads or crack plastics
• Keep removed fasteners organized to ensure correct reassembly

This oven door gasket assembly seals the door to the oven frame to keep heat in and prevent hot air leaks. Replacing a worn seal restores proper preheat times, temperature stability, and more consistent baking performance.

• Forms a heat-resistant seal between the oven door and front frame
• Helps reduce heat loss and maintain set oven temperatures
• Common fix for heat leaking around the door, long preheat times, and uneven baking/roasting
• Replace if the gasket is torn, frayed, flattened, brittle, or missing retainer ends

• Disconnect power at the breaker and allow the oven to cool completely
• Open the door and remove the old gasket from its retainers; note clip/hook locations and orientation
• Clean the sealing surface/channel before installing
• Install the new gasket without stretching; fully seat all retainers and verify the door closes evenly

This replacement screw secures appliance components and panels. Use it to replace a missing, stripped, or rusty fastener to restore a tight, rattle-free fit and keep assemblies properly aligned.

• Fastens brackets, trim, and panels securely to the appliance frame
• Replaces lost, worn, or corroded hardware
• Helps correct loose or wobbly parts and misalignment
• Reduces vibration or rattling caused by loose fasteners

• Disconnect power (and gas, if applicable) before servicing
• Match to the original and replace one-for-one to ensure correct length/thread
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• If multiple screws secure a part, loosen/tighten evenly to maintain alignment

This replacement door handle restores a secure, comfortable grip on your appliance door. A worn or broken handle can make opening the door difficult and unsafe; swapping it returns normal operation and appearance.

• Provides the leverage needed to open and close the door smoothly
• Helps resolve issues like loose, cracked, or missing handle
• Improves safety by giving a stable handhold
• Restores original fit and finish when the old handle is worn or damaged

• Unplug power and let the appliance cool completely before starting
• Support the door and remove mounting screws from the interior side as applicable
• Transfer any end caps or trim pieces from the old handle if required
• Do not overtighten screws to avoid cracking the handle or door panel

The End Cap is an OEM part for GE ranges. This part serves as the finishing piece for the range's handle, fitting onto either end to provide a polished look and to help secure the handle in place. The end cap is crucial for both the aesthetic appeal and the functionality of the range's door, ensuring that users can safely and comfortably open and close the oven door without encountering sharp or unfinished edges.

Causes of damage to the end cap can include physical impacts, such as accidental knocks or forceful opening/closing of the oven door, and material fatigue from regular use over time. 

Symptoms of a bad End Cap include:

• The handle feeling loose or wobbly 
• Visible cracks, breaks, or significant wear on the end cap 
• The end cap becoming detached from the handle 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This kick panel assembly replaces the bottom toe grille on compatible refrigerators to restore the finished look and help direct airflow. It refits under the cabinet for a clean, factory appearance. What it does:

• Covers the refrigerator's lower front opening for a finished exterior and to protect internal components
• Directs air flow at the base to support proper ventilation
• Helps prevent debris from entering the lower service area
• Restores missing or damaged trim that can affect appearance and clearance

• Basic removal of the old panel and fastening of the new panel with existing screws/clips; keep fasteners for reuse if undamaged
• Handle gently to avoid scratching painted or plastic surfaces during install
• Disconnect power only if required to access lower service area; follow appliance safety guidelines