Parts for Hot Point RGA724EK2WH: 04 - Door & Drawer Parts

This oven rack is a replacement wire shelf that supports cookware and bakeware for standard ranges and ovens. It restores proper cooking clearance and helps maintain even heat circulation inside the oven. What it does:

• Provides a stable shelf for pots, pans and baking sheets during cooking or baking.
• Restores correct rack positioning when the original rack is missing, bent, or worn.
• Helps maintain proper airflow and even heat distribution by holding items off the oven floor.
• Fits into existing left/right rack supports and slides into place on oven rack guides.

• Remove power to the appliance before accessing the oven interior for safety.
• Install by sliding the rack into the oven's existing rack guides until fully seated.
• Handle with care; edges can be sharp and the rack will be hot after use.

This replacement oven rack restores a safe, level surface for cookware inside the oven cavity. Replace a missing, bent, or damaged rack so you can load, slide, and position pans at the correct height.

• Supports bakeware and cookware in the oven; slides on the factory side rails
• Helps maintain proper spacing from heating elements for consistent results
• Common symptoms: rack is warped/bent, broken welds, flaking finish/rust, or it no longer slides smoothly
• Restores full oven capacity when a rack is missing

• Allow the oven to cool completely before handling racks
• To install, align with the side supports, tilt the front slightly upward to clear the stops, and slide into position
• Ensure both sides are fully seated and level before use
• Refer to your owner's manual for self-clean cycle recommendations regarding rack removal

This broiler pan grid is the oven rack insert that holds food above the broil pan to promote even browning and let drippings fall away. It restores broiling performance for ovens using a two-piece broil pan set. What it does:

• Supports meats and vegetables during broiling so heat circulates around food for better sear and browning
• Allows drippings to fall into the lower broil pan to reduce smoke and flare-ups
• Replaces a missing, warped, or damaged grid that can cause uneven cooking or food slipping through
• Fits into the matching broil pan to restore original broiling configuration

• Ensure oven is off and grid has cooled before handling or installing
• Place grid into the broil pan with grid edges seated securely in the pan
• Clean after use with warm, soapy water; avoid harsh abrasives that can damage the finish

This broil pan is the oven tray designed to catch drippings and hold food while broiling, making cleanup easier and helping food brown under high heat. Fits compatible GE ovens that use this factory broil pan. What it does:

• Holds food close to the broiler element for searing and browning.
• Collects grease and drippings to reduce smoke and make cleanup faster.
• Supports broiling racks or grids (when used with compatible inserts).
• Helps maintain consistent broil performance when the correct pan is in place.

• One broil pan (1 piece)

• Allow the oven to cool and disconnect power before handling or installing parts.
• Slide the pan onto the oven broil supports or into the broiler compartment until seated.
• Use oven mitts when removing after use; clean per manufacturer recommendations.

This mounting screw secures appliance components to the chassis for a tight, rattle-free fit. Replacing a missing, stripped, or corroded fastener helps keep panels, brackets, or burner assemblies properly aligned and secure.

• Fastens designated parts to the appliance frame or mounting points
• Helps maintain proper alignment of panels, trim, brackets, or burner assemblies
• Restores hold when the original screw is worn, rusted, or lost
• Symptoms include loose or wobbly components, rattling/vibration, or visible gaps

• Disconnect power; allow all surfaces to cool. For gas units, also shut off the gas supply.
• Use the correct driver/bit; avoid cross-threading.
• If mating threads or clip/nut are damaged, repair or replace them before installing.
• Tighten until secure; do not overtighten to prevent stripping.

This oven door gasket assembly seals the door to the oven frame to keep heat in and prevent hot air leaks. Replacing a worn seal restores proper preheat times, temperature stability, and more consistent baking performance.

• Forms a heat-resistant seal between the oven door and front frame
• Helps reduce heat loss and maintain set oven temperatures
• Common fix for heat leaking around the door, long preheat times, and uneven baking/roasting
• Replace if the gasket is torn, frayed, flattened, brittle, or missing retainer ends

• Disconnect power at the breaker and allow the oven to cool completely
• Open the door and remove the old gasket from its retainers; note clip/hook locations and orientation
• Clean the sealing surface/channel before installing
• Install the new gasket without stretching; fully seat all retainers and verify the door closes evenly

This replacement screw secures appliance components and panels. Use it to replace a missing, stripped, or rusty fastener to restore a tight, rattle-free fit and keep assemblies properly aligned.

• Fastens brackets, trim, and panels securely to the appliance frame
• Replaces lost, worn, or corroded hardware
• Helps correct loose or wobbly parts and misalignment
• Reduces vibration or rattling caused by loose fasteners

• Disconnect power (and gas, if applicable) before servicing
• Match to the original and replace one-for-one to ensure correct length/thread
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• If multiple screws secure a part, loosen/tighten evenly to maintain alignment

This replacement door handle restores a secure, comfortable grip on your range or wall oven door. Swap it in to fix a broken or loose handle and bring back safe, reliable door operation and a clean, finished look.

• Provides the handhold and leverage needed to open and close the oven door
• Replaces cracked, stripped, or missing handles to restore normal function
• Common symptoms: loose/wobbly handle, broken ends, handle falls off, difficulty opening/closing
• Helps maintain the door's finished appearance

• Disconnect power and allow the appliance to cool completely before starting
• Protect glass and finishes; support the door while working
• Access the handle mounting screws from the inside of the door; note spacer/trim orientation and transfer as removed
• Tighten screws evenly and avoid overtightening; verify smooth door operation

This replacement door handle restores a secure, comfortable grip on your appliance door. A worn or broken handle can make opening the door difficult and unsafe; swapping it returns normal operation and appearance.

• Provides the leverage needed to open and close the door smoothly
• Helps resolve issues like loose, cracked, or missing handle
• Improves safety by giving a stable handhold
• Restores original fit and finish when the old handle is worn or damaged

• Unplug power and let the appliance cool completely before starting
• Support the door and remove mounting screws from the interior side as applicable
• Transfer any end caps or trim pieces from the old handle if required
• Do not overtighten screws to avoid cracking the handle or door panel

The End Cap is an OEM part for GE ranges. This part serves as the finishing piece for the range's handle, fitting onto either end to provide a polished look and to help secure the handle in place. The end cap is crucial for both the aesthetic appeal and the functionality of the range's door, ensuring that users can safely and comfortably open and close the oven door without encountering sharp or unfinished edges.

Causes of damage to the end cap can include physical impacts, such as accidental knocks or forceful opening/closing of the oven door, and material fatigue from regular use over time. 

Symptoms of a bad End Cap include:

• The handle feeling loose or wobbly 
• Visible cracks, breaks, or significant wear on the end cap 
• The end cap becoming detached from the handle 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Bumper is an OEM part for GE ranges. It is located on the sides of the oven drawer and serves as a cushion to prevent noise, vibration, and wear. As time goes on, regular use of the appliance can cause it to become damaged or worn out.

Causes of a bad bumper can include wear and tear from regular use, deterioration of the material over time, or damage from excessive force when closing the door.

Symptoms of a bad Bumper include:

• Excessive noise
• Difficulty in sliding the drawer
• Misalignment
• Wear, and increased friction

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This aluminum foil panel is a thin interior liner used inside the freezer/refrigerator compartment to protect internal components and provide a smooth reflective surface. It restores the cabinet interior and helps maintain proper airflow and defrost performance. What it does:

• Covers and protects the cabinet back/evaporator area from direct contact and debris
• Provides a smooth, reflective surface that assists with even cold distribution
• Helps prevent direct frost buildup on the cabinet back when installed correctly
• Common symptoms: torn, dented, or missing foil; visible corrosion or gaps behind the evaporator; increased frost or poor temperature stability

• One aluminum foil panel

• Install with the refrigerator unplugged and after removing stored food; follow OEM instructions for panel removal and reattachment
• Handle carefully to avoid sharp edges and bending the foil; wear gloves if needed
• Ensure proper alignment and secure all fasteners to restore original fit and seal