Parts for Hot Point RGA820DED1WW: 04 - Door & Drawer Parts

This replacement oven rack restores a safe, level surface for cookware inside the oven cavity. Replace a missing, bent, or damaged rack so you can load, slide, and position pans at the correct height.

• Supports bakeware and cookware in the oven; slides on the factory side rails
• Helps maintain proper spacing from heating elements for consistent results
• Common symptoms: rack is warped/bent, broken welds, flaking finish/rust, or it no longer slides smoothly
• Restores full oven capacity when a rack is missing

• Allow the oven to cool completely before handling racks
• To install, align with the side supports, tilt the front slightly upward to clear the stops, and slide into position
• Ensure both sides are fully seated and level before use
• Refer to your owner's manual for self-clean cycle recommendations regarding rack removal

This broiler pan grid is the oven rack insert that holds food above the broil pan to promote even browning and let drippings fall away. It restores broiling performance for ovens using a two-piece broil pan set. What it does:

• Supports meats and vegetables during broiling so heat circulates around food for better sear and browning
• Allows drippings to fall into the lower broil pan to reduce smoke and flare-ups
• Replaces a missing, warped, or damaged grid that can cause uneven cooking or food slipping through
• Fits into the matching broil pan to restore original broiling configuration

• Ensure oven is off and grid has cooled before handling or installing
• Place grid into the broil pan with grid edges seated securely in the pan
• Clean after use with warm, soapy water; avoid harsh abrasives that can damage the finish

This broil pan is the oven tray designed to catch drippings and hold food while broiling, making cleanup easier and helping food brown under high heat. Fits compatible GE ovens that use this factory broil pan. What it does:

• Holds food close to the broiler element for searing and browning.
• Collects grease and drippings to reduce smoke and make cleanup faster.
• Supports broiling racks or grids (when used with compatible inserts).
• Helps maintain consistent broil performance when the correct pan is in place.

• One broil pan (1 piece)

• Allow the oven to cool and disconnect power before handling or installing parts.
• Slide the pan onto the oven broil supports or into the broiler compartment until seated.
• Use oven mitts when removing after use; clean per manufacturer recommendations.

This replacement screw secures trim and appliance panels with a compact 3/8" length and #8-18 thread, providing a simple fastener solution for loose or missing hardware. Fits a variety of appliance assemblies where short machine screws are used. What it does

• Fastens panels, trims, brackets, and small components that use #8-18 threaded holes
• Restores secure attachment for loose or rattling parts
• Replaces stripped or missing short screws to prevent gaps or movement
• Small size is suited for shallow mounting areas and sheet-metal attachments

• One screw

• Use the correct driver or bit to avoid stripping the head; a magnetic screwdriver helps with small fasteners
• Tighten until snug—do not overtighten to prevent thread damage or panel deformation
• Disconnect power to the appliance before working on internal components or near electrical connections
• Match those details for best fit and performance

This replacement door handle restores a secure, comfortable grip on your range or wall oven door. Swap it in to fix a broken or loose handle and bring back safe, reliable door operation and a clean, finished look.

• Provides the handhold and leverage needed to open and close the oven door
• Replaces cracked, stripped, or missing handles to restore normal function
• Common symptoms: loose/wobbly handle, broken ends, handle falls off, difficulty opening/closing
• Helps maintain the door's finished appearance

• Disconnect power and allow the appliance to cool completely before starting
• Protect glass and finishes; support the door while working
• Access the handle mounting screws from the inside of the door; note spacer/trim orientation and transfer as removed
• Tighten screws evenly and avoid overtightening; verify smooth door operation

The End Cap is an OEM part for GE ranges. This part serves as the finishing piece for the range's handle, fitting onto either end to provide a polished look and to help secure the handle in place. The end cap is crucial for both the aesthetic appeal and the functionality of the range's door, ensuring that users can safely and comfortably open and close the oven door without encountering sharp or unfinished edges.

Causes of damage to the end cap can include physical impacts, such as accidental knocks or forceful opening/closing of the oven door, and material fatigue from regular use over time. 

Symptoms of a bad End Cap include:

• The handle feeling loose or wobbly 
• Visible cracks, breaks, or significant wear on the end cap 
• The end cap becoming detached from the handle 

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Bumper is an OEM part for GE ranges. It is located on the sides of the oven drawer and serves as a cushion to prevent noise, vibration, and wear. As time goes on, regular use of the appliance can cause it to become damaged or worn out.

Causes of a bad bumper can include wear and tear from regular use, deterioration of the material over time, or damage from excessive force when closing the door.

Symptoms of a bad Bumper include:

• Excessive noise
• Difficulty in sliding the drawer
• Misalignment
• Wear, and increased friction

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This aluminum foil panel is a thin interior liner used inside the freezer/refrigerator compartment to protect internal components and provide a smooth reflective surface. It restores the cabinet interior and helps maintain proper airflow and defrost performance. What it does:

• Covers and protects the cabinet back/evaporator area from direct contact and debris
• Provides a smooth, reflective surface that assists with even cold distribution
• Helps prevent direct frost buildup on the cabinet back when installed correctly
• Common symptoms: torn, dented, or missing foil; visible corrosion or gaps behind the evaporator; increased frost or poor temperature stability

• One aluminum foil panel

• Install with the refrigerator unplugged and after removing stored food; follow OEM instructions for panel removal and reattachment
• Handle carefully to avoid sharp edges and bending the foil; wear gloves if needed
• Ensure proper alignment and secure all fasteners to restore original fit and seal