Parts for Hot Point RGA824DED1WW: 04 - Door & Drawer Parts

Replacement wire oven rack for electric ranges. Supports cookware inside the oven cavity. Order a new rack if yours is warped, rusted, or broken.

Broiler pan grid insert that holds food above the drip pan during broiling. Replace if your grid is warped, rusted, or has broken wires.

Broiler pan installs in your range oven to catch drippings and hold food during broiling. Replace if cracked, warped, rusted, or missing.

Replacement screw for electric and gas ranges. Secures internal components and panels. Needed when original hardware is stripped, missing, or lost during repairs.

This replacement screw secures trim and appliance panels with a compact 3/8" length and #8-18 thread, providing a simple fastener solution for loose or missing hardware. Fits a variety of appliance assemblies where short machine screws are used. What it does

• Fastens panels, trims, brackets, and small components that use #8-18 threaded holes
• Restores secure attachment for loose or rattling parts
• Replaces stripped or missing short screws to prevent gaps or movement
• Small size is suited for shallow mounting areas and sheet-metal attachments

• One screw

• Use the correct driver or bit to avoid stripping the head; a magnetic screwdriver helps with small fasteners
• Tighten until snug—do not overtighten to prevent thread damage or panel deformation
• Disconnect power to the appliance before working on internal components or near electrical connections
• Match those details for best fit and performance

Replacement broiler pin for gas ranges. This metal pin secures the broiler drawer in place. Order a new pin if your original is bent, broken, or missing.

Replace your range's broken or cracked door handle. This pocket-style handle attaches to the oven door front, allowing you to safely open and close it.

Broiler hinge assembly for gas ranges. Attaches and supports the broiler drawer for smooth open/close operation. Replace if cracked, bent, or worn.

Broiler hinge assembly for gas ranges. Attaches to the broiler door to allow smooth opening and closing. Replace if cracked, broken, or worn.

Black door handle for range ovens. Installs on the front door to provide a secure grip for opening and closing. Replace if cracked, broken, or worn.

Finishing piece that fits on either end of your range door handle. Replace if cracked, broken, or missing to restore appearance and secure the handle.

The Bumper is an OEM part for GE ranges. It is located on the sides of the oven drawer and serves as a cushion to prevent noise, vibration, and wear. As time goes on, regular use of the appliance can cause it to become damaged or worn out.

Causes of a bad bumper can include wear and tear from regular use, deterioration of the material over time, or damage from excessive force when closing the door.

Symptoms of a bad Bumper include:

• Excessive noise
• Difficulty in sliding the drawer
• Misalignment
• Wear, and increased friction

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement spring for gas range broil door mechanism. Installs on the door assembly to provide tension and support. Needed when original is broken or worn.

This aluminum foil panel is a thin interior liner used inside the freezer/refrigerator compartment to protect internal components and provide a smooth reflective surface. It restores the cabinet interior and helps maintain proper airflow and defrost performance. What it does:

• Covers and protects the cabinet back/evaporator area from direct contact and debris
• Provides a smooth, reflective surface that assists with even cold distribution
• Helps prevent direct frost buildup on the cabinet back when installed correctly
• Common symptoms: torn, dented, or missing foil; visible corrosion or gaps behind the evaporator; increased frost or poor temperature stability

• One aluminum foil panel

• Install with the refrigerator unplugged and after removing stored food; follow OEM instructions for panel removal and reattachment
• Handle carefully to avoid sharp edges and bending the foil; wear gloves if needed
• Ensure proper alignment and secure all fasteners to restore original fit and seal