Parts for Kenmore 790.45139510 (79045139510, 790 45139510): Door / Drawer Parts

This replacement glass panel restores the viewing window and heat barrier in your oven door. Swap a damaged pane to maintain safe operation, proper heat retention, and a clean, clear view of what's cooking.

• Provides the door's viewing window and helps insulate the oven cavity
• Restores visibility into the oven during baking and broiling
• Replace if the glass is cracked, shattered, scratched, or permanently stained
• Common symptoms include visible damage, heat loss, uneven baking, or exterior door area feeling hotter than normal

What's included: 1 glass panel Install notes:

• Disconnect power (and shut off gas, if applicable) and allow the appliance to cool completely
• Wear cut-resistant gloves and eye protection; tape over broken glass before removal
• Note pane orientation, spacers, and seals; transfer any hardware in the same positions
• Avoid overtightening fasteners and clean fingerprints from the new glass after installation

The Oven Door Seal is an OEM replacement part for select Frigidaire oven and range models. It fits around the outer edge of the oven door, creating an insulating barrier that locks in heat. The seal is critical for efficient baking and broiling by preventing heat loss from the oven cavity.

Symptoms of a faulty oven door seal include:

• Leaks of hot air or smoke around the oven door when in use  
• Inconsistent or improper cooking results from uneven heating  
• The oven not reaching or maintaining the set temperature
• The outer oven door and surrounding area getting hot during use

Causes include shrinkage and cracks from years of exposure to heat. Grease and residue accumulating in the door channel could also compromise the seal's fit. 

This OEM replacement is compatible with Electrolux, Gibson, Kelvinator, and Kenmore brands.

This drum roller supports the dryer drum and helps it turn smoothly, reducing friction and noise. Replacing a worn roller restores quieter operation and helps prevent drum wobble and uneven tumbling. What it does:

• Supports the rotating drum so it spins freely and evenly.
• Reduces squeaks, grinding noises and excessive vibration from a worn wheel.
• Helps prevent drum wobble that can lead to uneven drying or wear on other components.
• Works with the drum shaft/bearing system to maintain proper drum alignment.

• Disconnect power (and gas, if applicable) before starting any service.
• Remove the dryer drum to access and replace the roller—follow your model's service manual or OEM instructions.
• Inspect adjacent rollers, bearings and the shaft for wear while the drum is removed.

This handle assembly replaces a broken, cracked, or missing refrigerator door handle so the door opens and closes securely and looks finished. Durable molded construction matches the original fit and lever action. What it does:

• Provides the gripping surface and mounting points to open and close the refrigerator door
• Restores proper door control when the original handle is cracked, loose, or detached
• Keeps the door aligned with its latch area for smooth operation
• Prevents hand contact with damaged edges and improves cabinet appearance

• Unplug the appliance or switch off power before beginning work to avoid injury
• Remove any trim or screws holding the old handle; keep fasteners if they are undamaged and listed for reuse
• Align the new handle with the mounting bosses and fasten securely without over-tightening to avoid cracking the plastic
• If the handle uses hidden clips or adhesive trim, verify clip engagement and door operation before finishing

This two-piece broiler pan and insert set creates a proper broiling surface in your range or wall oven. The vented top supports food while drippings collect below, helping reduce smoke and splatter for more consistent browning.

• Provides a slotted broiling surface that lets fats drain into the pan below
• Helps protect the oven cavity from spills and reduce smoke during broiling
• Replaces a missing, warped, rusted, or heavily stained broiler pan assembly
• If existing pan causes uneven browning, smoke, or odors, replacing it can restore broiling performance

• Allow the oven and racks to cool completely before handling
• Wash the new pan and insert before first use; dry thoroughly
• Set rack height per your owner's manual; seat insert on the pan and slide onto the rack
• Do not cover the insert with foil unless your manual permits; keep clear of the broil element

The Broiler Pan Assembly is an OEM part for Frigidaire ranges and ovens. This part includes both the broiler pan and the grill rack, designed to catch drippings and promote even cooking when broiling foods.  This assembly includes pan and insert.

Causes of a bad broiler pan assembly can include wear and tear from regular use, warping or rusting due to high temperatures, or damage from improper cleaning methods.  

Symptoms of a bad Broiler Pan Assembly include:

• Visible warping or rust on the pan or rack
• Difficulty in cleaning due to persistent stains or damage
• Uneven cooking results when broiling
• The pan or rack no longer fitting securely in the oven

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts