Parts for Electrolux EIED2CAQSW00: 03 - Door Parts

This is a replacement clear glass refrigerator shelf that restores a flat, easy-to-clean surface for holding food and containers. Installs into shelf supports to return usable storage space and visibility inside the compartment. What it does:

• Provides a sturdy, flat surface for storing food and containers
• Easy-to-clean tempered glass resists staining and spills
• Restores proper spacing and visibility on the shelf level
• Replace broken, chipped, or cracked shelves to prevent food damage and safety hazards

• Remove food and supports before installing; handle glass with gloves to avoid cuts
• Set shelf into side supports evenly, then lower into position—do not force
• Inspect mounting rails or clips for damage and replace if worn

This inner oven door glass panel replaces a cracked, broken or cloudy inner door glass to restore a clear view of the oven cavity and help the door maintain proper heat containment. Fits the oven door assembly where inner glass is used. What it does

• Replaces damaged or shattered inner oven door glass to remove visible cracks or clouding.
• Helps the door retain proper thermal separation so cooking performance is not affected by damaged glass.
• Stops rattling or slap caused by loose or broken inner glass inside the door.
• Restores a clean, unobstructed view of food inside the oven.

• Disconnect power (and gas supply if applicable) and allow the oven to cool completely before servicing.
• Wear cut-resistant gloves and eye protection; handle glass carefully to avoid injury.
• Many installations require removing the oven door and separating the outer and inner door panels—retain all screws and hardware for reassembly.
• Tighten fasteners evenly; do not overtighten to avoid cracking.

This metal refrigerator door hinge replaces a worn or damaged hinge to restore smooth, secure door movement and proper alignment. Installing the correct hinge helps maintain a tight seal and prevents sagging or uneven closing. What it does:

• Supports and pivots the refrigerator door for reliable opening and closing.
• Keeps the door aligned so the gasket seals properly and cooling efficiency is preserved.
• Replaces worn or bent hardware that can cause a sagging, noisy, stiff, or misaligned door.
• Simple mechanical replacement — no electronics or sensors involved.

• Unplug the appliance and remove items from the door before starting; support the door to prevent drops or injury.
• Use the correct hand tools; keep fasteners and washers in order for reassembly.
• Reposition and test the door swing and seal after installation; adjust hinge fasteners evenly to avoid binding.

This tappet is a small actuator component that transfers motion between the control mechanism and the driven part, restoring reliable mechanical engagement. It's a direct-fit replacement when the original tappet is worn or broken. What it does:

• Transmits motion from the control or actuator to the linked mechanism for proper operation
• Restores positive engagement when worn tappet causes intermittent or no response
• Commonly replaced for symptoms like controls that don't engage, cycles that fail to advance, or loose/mechanical play where a solid link is expected

• One tappet replacement part

• Install only with power disconnected to the appliance
• Minor disassembly of the control or housing may be required; keep fasteners organized
• Inspect mating parts and retainers for wear and replace if damaged

This catch is the small retention piece that mates with a latch or hook to keep a door, drawer, or panel securely closed. Replacing a worn catch restores proper closure and helps prevent nuisance openings and interruptions during use.

• Engages the mating latch/strike to hold the assembly closed
• Helps maintain alignment and sealing where the design requires it
• Wear or damage can cause loose closure, popping open, rattling, or difficulty latching
• Replace if cracked, deformed, or missing for reliable closure

• Disconnect power (and water supply if applicable) before servicing
• Wear cut-resistant gloves; cabinet and panel edges can be sharp
• Note the original orientation and transfer any reusable hardware
• Align with the mating latch/strike and test for smooth, secure closure; adjust as needed

This electrical switch controls a basic on/off or signal function inside the appliance to restore normal operation of the affected circuit. Replaces a failed or worn switch to help the unit respond to user inputs. What it does:

• Opens or closes an electrical circuit to enable a component to power on or off
• Commonly used where a user or mechanism needs to trigger a function
• Symptoms it can fix: appliance not responding to a control, intermittent power to a component, or a non-functioning user control
• Works as a direct replacement for the OEM switch assembly when matching part number and connector

• Disconnect power to the appliance before starting any repair
• Handle wiring and terminals carefully; secure all connections and restore any mounting clips or screws
• Test the appliance function after installation and restore power only when safe