Parts for Electrolux FGES3065PBD: 05 - Door Parts

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

A decorative trim piece that restores the finished edge and appearance of the appliance door. Replaces worn or damaged trim to improve aesthetics and help keep the door edge sealed and protected. What it does:

• Provides a finished decorative edge to the appliance door or panel
• Helps secure and align the outer door or panel for a consistent fit
• Covers gaps and hides fasteners for improved appearance
• Commonly replaced for cracked, dented, or faded trim

• One trim piece as shown

• Disconnect power to the appliance before starting any repair
• Remove door or panel fasteners as needed to access the trim; keep hardware organized
• Use gentle prying to avoid scratching adjacent surfaces; avoid forcing the trim into place

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

The Inner Door Glass is an  OEM replacement part for Frigidaire ranges. It is responsible for providing a safe viewing window into the oven cavity while protecting interior components from external damage.  

Causes of a bad inner door glass include normal wear and tear such as chips or cracks developing from years of use. Accidental impact or thermal shocks from sudden temperature changes can also compromise the integrity of the glass.

Symptoms of a bad inner door glass:

• Cracks or breaks visible in the glass
• Difficulty seeing into the oven cavity clearly 
• Increased risk of heat escaping when the oven is in use
• Potential safety hazards if glass cracks or shatters  

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

Replacement glass panel for the oven door. It restores a clear viewing window and helps maintain proper insulation when the original glass is cracked, shattered, or discolored.

• Forms the see-through window in the oven door
• Contributes to the door's thermal barrier to help maintain set temperature
• Replace if the glass is cracked, shattered, fogged, or has sharp edges
• Improves visibility and refreshes the appliance's appearance

• Disconnect electrical power; shut off gas supply for gas ranges
• Allow the oven to cool completely; wear cut-resistant gloves and eye protection
• Support the door and remove it if required; transfer any trim/retainers from the old glass
• Handle glass by the edges only and avoid overtightening fasteners during reassembly

This glass spacer positions and cushions refrigerator glass components to maintain proper spacing and reduce rattling or contact damage. It restores correct alignment for secure, quiet operation and helps prevent chipping or glass stress. What it does:

• Keeps glass shelves/panels separated and aligned to prevent rubbing, chipping, or cracking.
• Cushions impact and dampens vibration that can cause rattling or noisy doors/drawers.
• Helps maintain proper spacing for smooth insertion and removal of shelves or panels.
• Replaces worn, cracked, or missing spacers that allow glass movement or uneven seating.

• One glass spacer

• High-level replacement only; confirm spacer orientation and seating before final assembly.
• Handle glass and spacer carefully; wear gloves and eye protection to avoid cuts.
• Do not overtighten nearby fasteners—secure snugly to avoid cracking the glass.
• Replace the glass panel before installing the spacer if damaged or fractured.

A small mounting spacer used to position and support appliance components for correct alignment and stable operation. Replaces a worn or missing spacer to help restore proper fit between panels and parts. What it does:

• Keeps panels, brackets, or components spaced correctly to prevent rubbing and misalignment
• Helps reduce vibration and rattling caused by gaps or loose fits
• Restores correct clearance for moving parts that need precise spacing
• Used wherever a fixed gap or support is required between parts

• Disconnect power (and fuel or water if applicable) before beginning any repair
• Access may require removing outer panels, trim, or adjoining components
• Keep orientation and placement the same as the original spacer; install snugly but avoid over-tightening
• If other parts show wear or damage, inspect and replace them as needed for a complete repair

This support bracket secures and stabilizes appliance components, restoring proper alignment and stopping movement. It's a simple replacement that helps reduce rattling and prevents panels or assemblies from shifting during use. What it does:

• Provides a rigid mounting point to hold panels, trim, or internal assemblies in place
• Restores proper alignment when a worn or broken bracket causes gaps or looseness
• Reduces vibration and rattling caused by a damaged or missing support
• Keeps connected parts from shifting, which can prevent further wear or damage

• Disconnect power to the appliance before beginning any repair
• Verify the bracket orientation and fit against the mating surface before fastening
• Use the factory screw locations and hardware; tighten screws securely but avoid over-torquing

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts