Parts for Frigidaire FED353CCWG: 05 - Door Parts

Oven door gasket creates a tight seal to maintain temperature. Replace if torn, flattened, or crispy. Clips into door frame. Confirm fit by model number.

This refrigerator/freezer door gasket creates an airtight seal around the door to help maintain proper temperature and reduce energy use. It replaces a worn or damaged seal to improve cooling and reduce frost buildup. What it does:

• Seals the cabinet to keep cold air in and warm air out
• Helps prevent excess frost and moisture inside the compartment
• Reduces compressor run-time caused by air leaks
• Restores proper door alignment and consistent cooling

• Disconnect power and remove food from affected compartment before starting
• Remove the old gasket and thoroughly clean and dry the gasket channel before installing
• Press the new gasket into the channel evenly, starting at a corner and working around the door
• Check the seal by closing the door; adjust or reseat as needed for a uniform contact

White plastic spacer that mounts between the oven handle and door. Replace if cracked, broken, or missing to restore proper handle alignment and appearance.

This white handle trim restores the finished look and grip area on compatible appliance doors. It replaces a cracked, faded, or missing trim piece to improve appearance and create a clean edge around the handle area. What it does

• Covers and protects the handle mounting area while providing a smooth, finished appearance
• Replaces trim that is cracked, warped, discolored, or otherwise damaged
• Helps prevent sharp edges and improves the grip area for normal door use
• Matches factory styling so the door looks original and uniform

• One white handle trim piece as shown

• Basic removal of the old trim and reattachment of the new trim; fasteners and clips are present before installation
• Use proper tools to avoid scratching surrounding surfaces; support the door or panel if needed
• Disconnect power or follow appliance-specific safety steps when working near electrical components
• If fasteners or clips are missing or damaged, replace them before completing installation

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

Cork and rubber spacer for ovens and ranges. Provides cushioning and spacing between components. Replace if worn, cracked, compressed, or missing.

Mounting plate that secures the power cord set to the back of your range. Replace if the original plate is cracked, broken, or missing during installation.

Cork and rubber spacer for ovens and ranges. Provides cushioning and spacing between components. Replace if worn, cracked, compressed, or missing.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

Replacement machine screw used to secure appliance panels and internal components, restoring a stable fit and reducing rattling. Matches a 10-32 thread with a 17/32-inch length for original fastener locations. What it does:

• Fastens panels, trim pieces, and internal brackets; a missing or damaged screw can cause loose panels or rattling noises.
• Secures knobs, control housings and small assemblies to prevent wobble or misalignment.
• Restores proper fit for components so doors and access panels sit evenly and function reliably.

• Disconnect power (unplug or shut off circuit) before accessing components.
• Use the correct driver and tighten by hand; avoid overtightening to prevent stripped threads or cracked plastic.
• Keep any original washers or clips and reinstall them with the screw.

Secures panels and components in your range or oven. Replace if broken, bent, or missing to prevent shifting and reduce vibration noise. Confirm fit.