Parts for Frigidaire FFGF3056TWA: Door Parts

This Door Trim Kit replaces the perimeter trim on the appliance door, restoring a clean, factory-finished look and secure fit of the door frame components. Use when the original trim is cracked, warped, missing, or discolored.

• Frames and protects the outer edge of the door while concealing fasteners for a finished appearance
• Helps maintain proper placement of door panels/liners where designed
• Common symptoms: cracked or missing trim, loose/rattling trim, visible gaps, or discoloration
• Replace when trim no longer stays attached or is damaged

• Disconnect power to the appliance before servicing; allow all surfaces to cool
• Open the door and note trim orientation; take a photo for reference
• Use non-marring tools and protective gloves to avoid scratching finishes or injury
• After installation, verify the door opens/closes smoothly and does not rub or bind

This door trim kit restores the finished edge around the appliance door, covering raw edges and fasteners. Replace worn or missing trim to refresh the look and help keep the outer door panel properly seated. What it does:

• Finishes the perimeter of the door and conceals mounting hardware
• Helps retain and align the outer door panel or glass
• Replaces cracked, warped, loose, or missing trim pieces
• Typical symptoms include gaps around the door, loose or rattling edges, or cosmetic damage

• One door trim kit

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; door edges and trim can be sharp
• Support or remove the door as required by your model; note screw locations and lengths
• Transfer any clips/screws from the original trim and check door alignment and operation after installation

The Outer Oven Door Panel is an OEM component specially designed for Frigidaire ranges. Constructed of durable steel, it forms the front facade of the oven cavity entrance. 

Prolonged heating cycles from baking subject panels to thermal stresses that cause warping and paint discoloration over time due to typical door element heating and cooling. Fatigue jeopardizes functionality.

Causes relate to the normal expansion and contraction cycles expected of an oven door exposed to repeated preheating. Impacts pose abrupt risks to the protective steel facing.  

Symptoms of a bad door panel involve:

• Unsightly stain pigment changes dimming the finish
• Noticeable bowing or tweaks in planar surfaces  
• Gaps appearing at seam borders from structural strain

Replacing with this OEM Frigidaire panel restores a smooth, attractive entrance for cooking tasks. Compatibility fits Kenmore, Electrolux, and Gibson brands ensuring steady performance with upgraded cosmetics.

This is the glass panel used in the oven door window. Replace it to restore a clear view into the oven and maintain the door's proper heat barrier if the original pane is cracked, shattered, or damaged.

• Forms the viewing window and thermal barrier in the oven door
• Helps the oven retain heat for consistent cooking
• Direct replacement for a cracked, shattered, or missing pane
• Typical symptoms: visible cracks, shattered glass, rattling fragments, or reduced visibility

• Disconnect power or gas and allow the oven to cool completely before service
• Wear cut-resistant gloves and eye protection; handle broken glass with care
• Support the door; remove the door and any trim as outlined in your model's service information
• Transfer any reusable brackets/trim from the original glass and avoid overtightening fasteners

A replacement shield that protects internal refrigerator components from damage and keeps nearby parts securely covered. Replaces a worn or cracked cover so panels and wiring stay shielded during normal use. What it does:

• Covers and protects vulnerable components from accidental contact and debris
• Helps maintain proper clearance between parts to prevent rubbing or interference
• Restores a finished appearance where the original shield is damaged
• Useful when the original cover is cracked, broken, or missing

• Always unplug the appliance or shut off power at the breaker before servicing
• Handle the part carefully to avoid sharp edges and to prevent further damage
• Basic tools (screwdriver or nut driver) may be required for removal and installation

This insulation panel fits inside the refrigerator cabinet to help maintain consistent temperatures and reduce heat transfer. It preserves cooling efficiency and helps minimize frost and condensation when the appliance is operating properly. What it does:

• Provides thermal barrier between the cabinet and outer shell to help maintain internal temperature
• Helps reduce frost buildup and interior condensation when sealing and cooling systems are functioning
• Can improve energy efficiency by minimizing unwanted heat gain
• Dampens vibration and can reduce operating noise from the compressor area

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle insulation carefully—avoid compressing or tearing the material to retain thermal performance
• Remove interior panels or shelving as needed to access the installation area; keep track of fasteners
• If the original insulation is damaged or contaminated, replace it and check nearby seals and gaskets for proper fit

The Inner Door Glass is an  OEM replacement part for Frigidaire ranges. It is responsible for providing a safe viewing window into the oven cavity while protecting interior components from external damage.  

Causes of a bad inner door glass include normal wear and tear such as chips or cracks developing from years of use. Accidental impact or thermal shocks from sudden temperature changes can also compromise the integrity of the glass.

Symptoms of a bad inner door glass:

• Cracks or breaks visible in the glass
• Difficulty seeing into the oven cavity clearly 
• Increased risk of heat escaping when the oven is in use
• Potential safety hazards if glass cracks or shatters  

This genuine Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore gas ranges.

This replacement cabinet frame restores the appliance's front trim for a clean, finished appearance and proper panel alignment. It helps keep edges covered and maintains the door/cabinet fit. What it does:

• Provides the front trim/frame that supports and aligns the appliance cabinet or door panels
• Covers exposed edges for a finished look and helps reduce drafts or light gaps
• Helps eliminate rattling or misalignment caused by a damaged or warped frame
• Matches OEM fit to replace a cracked, bent, or cosmetically damaged frame

• Disconnect power (and water for appliances with water) before beginning any work
• Basic hand tools typically needed; retain all fasteners from the original part for reassembly
• Handle carefully to avoid scratching the finish; check fit before tightening fasteners

The Handle Mounting Screw is an OEM part for Frigidaire ranges. This screw secures the handle to the oven door, ensuring it remains firmly attached and allows for easy opening and closing of the oven.

Causes of a bad handle mounting screw can include wear and tear from frequent use, over-tightening, or accidental impact that damages the threads or head of the screw.

Symptoms of a bad handle mounting screw include:

• The oven handle feeling loose or wobbly
• Difficulty in opening or closing the oven door
• The handle detaching from the door
• Visible damage or wear to the screw

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Seal is an OEM part for Frigidaire ranges. This seal creates a tight barrier to prevent heat from escaping during cooking. Maintaining a proper seal ensures that the oven operates efficiently, maintains the correct temperature, and provides even cooking results.

Causes of a bad range door seal can include wear and tear from regular use, exposure to high temperatures, or damage from cleaning tools.  

Symptoms of a bad range door seal include:

• Heat escaping from around the oven door
• Uneven cooking or longer cooking times
• Visible cracks, tears, or deformation on the seal
• The oven door not closing tightly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This spring-loaded hinge supports and controls the oven door's movement so it opens smoothly and closes firmly, helping the door seal properly and retain heat. Replacing a worn hinge restores proper door alignment and closing force.

• Provides the pivot and spring tension for controlled door opening/closing
• Helps the door sit flush against the gasket to maintain a proper heat seal
• Common symptoms: door won't fully close, sags or drops, won't hold at a mid-open position, heat escaping from the front
• Typical causes of failure: metal fatigue, spring wear, or hinge deformation from heavy use

• Disconnect power; for gas models, also shut off gas. Allow the oven to cool completely.
• Support the door and engage hinge locks or remove the door.
• Springs are under tension—use gloves and eye protection; do not disassemble the hinge.
• Align with the receivers/slots and test for smooth operation and full closure; consider replacing both for even tension.

The Door Handle is an OEM part for Frigidaire ovens. This handle is designed to provide a secure grip for opening and closing the oven door. It is essential for safely accessing the oven's interior, ensuring convenience and ease of use while cooking or cleaning.

Common causes of a bad handle include wear and tear from frequent use, impact damage from accidental bumps or falls, or exposure to high temperatures over time that can weaken the material.

Symptoms of a bad door handle include:

• The handle feeling loose or wobbly
• Visible cracks or breaks in the handle
• Difficulty in opening or closing the oven door
• The handle detaching from the door completely

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Handle is an OEM replacement part for Frigidaire electric ranges. Located on the oven door, this metal handle grants access to the cooking cavity. This black door handle measures 34.88 x 6 x 3.63 inches

Causes of a bad door handle can include cracks or breaks at welded connection points due to repeated opening/closing over several years.

Symptoms of a bad door handle include:

• Difficulty lifting or releasing due to compromised integrity
• Handle detaching from the door posing a risk of falling or injury  
• Visible cracks or stress fractures in chrome plating

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Vent Trim is an OEM part for Frigidaire ranges. This part frames and supports the oven's ventilation system, ensuring proper heat dispersal and maintaining the aesthetic integration of the range within the kitchen setup.  

Common causes for vent trim issues include physical impacts during cleaning or use, thermal deformation from continuous exposure to high temperatures, and general wear and tear over time.  

Symptoms of failing Vent Trim include:

• Loose or ill-fitting trim that may not stay in place
• Visible damage such as cracks or warping due to heat exposure
• Increased heat retention or abnormal heat outside the oven
• Aesthetic discrepancies that impact the overall look of the kitchen

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This surface burner cap fits gas ranges and cooktops. It sits atop the burner head to shape the flame and shield the burner from spills, helping restore smooth ignition and consistent, even heat output.

• Shapes and distributes the burner flame for more even cooking
• Protects the burner head from spills and debris
• Helps ensure reliable ignition and a stable, blue flame
• Common signs it's needed: missing/damaged cap, uneven or yellow flames, burner slow to light, rattling cap

What's included: One surface burner cap. Install notes:

• Turn the burner off and allow the cooktop to cool completely before servicing.
• Remove the grate and lift off the old cap; clean the burner head and ports if needed.
• Center the new cap on the matching burner head so it sits level and fully seated.
• Reinstall the grate and test; realign the cap if the flame is uneven.

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts