Parts for Frigidaire FGMC2766UDC: Door Parts

This replacement latch assembly secures the refrigerator or freezer door to ensure proper closure and reliable operation. It restores the door catch so the appliance can maintain an effective seal and help prevent cooling loss. What it does:

• Secures the door to keep it closed and aligned
• Replaces a broken, bent, or worn latch that prevents proper latching
• Helps reduce warm air entry caused by a door that won't stay shut
• Works as the mechanical catch that engages the door striker

• Disconnect power (unplug appliance) before servicing to avoid shock or injury.
• Remove the inner door panel or access trim as needed to reach the latch; keep screws and fasteners organized.
• Align the latch with the door striker and tighten screws securely without over-torquing.
• Test door operation several times after installation to ensure proper engagement and seal.

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This is a replacement glass panel for the appliance assembly. It restores a clear, intact barrier where the original glass was cracked, chipped, or missing—helping the unit operate safely and look like new. What it does:

• Replaces broken or shattered glass to restore the intended barrier or support surface
• Helps maintain safe operation by eliminating sharp edges and gaps
• Preserves proper appearance and fit of the assembly
• Typical symptoms: visible cracks, spider-web shatter, loose or rattling panel, missing glass

• One glass panel

• Disconnect power and allow all surfaces to cool before service; wear cut-resistant gloves and eye protection
• Support the assembly during disassembly to prevent drops or stress on hinges/frames
• Transfer any trim, brackets, gaskets, or insulation from the original panel as required
• Handle glass carefully by the edges; do not overtighten fasteners against glass

The Screw is an OEM replacement part for Frigidaire appliances. This screw is used to securely fasten components, such as panels, brackets, or internal parts, ensuring the appliance remains stable and functions correctly. Its precise design ensures a snug fit and reliable performance in the designated area of the appliance.

Over time, screws can become stripped, corroded, or loosened due to vibrations, frequent use, or environmental factors. A damaged or missing screw may lead to instability, misaligned components, or operational issues with the appliance.

Symptoms of a bad or missing screw include:

• Loose or misaligned panels or components
• Rattling or unusual noises during operation
• Difficulty in securing parts during repairs or adjustments
• Parts becoming detached or unstable

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This complete door assembly replaces a damaged or worn refrigerator door to restore a proper seal and appearance. It installs as a single unit to simplify replacement and get the door functioning correctly again. What it does:

• Replaces the full outer door structure, including the panel and internal mounting points
• Restores door alignment and helps maintain proper temperature by enabling a tight seal
• Eliminates visible damage, dents, or cracked surfaces that affect operation or appearance
• Supports attached components (hinges, gaskets, trim) when those parts are integral to the assembly

• Disconnect power and empty the door of contents before starting; have a second person assist—door assemblies are heavy and awkward.
• Verify hinge orientation and mounting hardware on your appliance; additional brackets or screws may be required.
• Inspect and reuse or replace door gasket, shelves, and trim as needed.

This complete outer door assembly replaces a damaged or worn refrigerator door panel to restore proper closure, insulation support, and appearance. It's a direct-fit replacement designed to return your appliance to factory condition. What it does:

• Replaces a dented, cracked, or cosmetically damaged outer door surface
• Restores proper door closure and helps maintain internal temperature by supporting the gasket
• Provides original mounting points for handles, trim, and interior components
• Helps eliminate drafts, cold loss, and moisture buildup related to a compromised door

• Disconnect power and empty the door of stored items before starting
• Two people are recommended for safe handling and alignment
• Transfer any hardware, handles, shelves, liners, or sensors from the old door unless new items are shown as included
• Adjust hinges per manufacturer instructions

This replacement front panel restores the exterior trim around the appliance control area, protecting switches and electronics while renewing the unit's appearance. Designed to match OEM fit and finish for a clean, factory look. What it does:

• Covers and protects the control area from spills, dust, and impact
• Provides the correct mounting surface and openings for buttons and displays
• Helps restore cosmetic appearance when original panel is cracked, dented, or faded
• Secures with factory clip or screw locations to maintain proper alignment

• Always disconnect power to the appliance before starting any repair.
• Installation typically requires removing trim screws/clips and lifting the old panel out of position.
• Keep all fasteners and verify clip orientation to ensure a tight fit.

This refrigerator door hinge lets the door pivot smoothly and maintain proper alignment for a secure, even seal. Replace a worn or damaged hinge to stop door sag, rubbing, or uneven closing and help restore normal operation. What it does:

• Provides a stable pivot point for the refrigerator door so it opens and closes correctly
• Restores proper door alignment to improve gasket sealing and cooling efficiency
• Stops symptoms like a sagging or misaligned door, noisy hinge operation, or door rubbing
• Durable metal construction designed for repeated use under normal household conditions

• One refrigerator door hinge

• Unplug the appliance or disconnect power before starting any repair
• Support the door while removing and installing the hinge to prevent injury or damage
• Keep fasteners and any small parts organized; tighten screws snugly but avoid over-torquing
• Adjust hinge and striker positions per manufacturer guidance

A small mounting spacer used to position and support appliance components for correct alignment and stable operation. Replaces a worn or missing spacer to help restore proper fit between panels and parts. What it does:

• Keeps panels, brackets, or components spaced correctly to prevent rubbing and misalignment
• Helps reduce vibration and rattling caused by gaps or loose fits
• Restores correct clearance for moving parts that need precise spacing
• Used wherever a fixed gap or support is required between parts

• Disconnect power (and fuel or water if applicable) before beginning any repair
• Access may require removing outer panels, trim, or adjoining components
• Keep orientation and placement the same as the original spacer; install snugly but avoid over-tightening
• If other parts show wear or damage, inspect and replace them as needed for a complete repair

This replacement door handle provides a secure grip to open and close your refrigerator door, restoring normal door operation and improving appearance. Designed as a direct-fit OEM-style handle for quick replacement. What it does:

• Replaces a cracked, broken or loose refrigerator door handle so the door can be opened and closed safely.
• Restores a comfortable grip and proper leverage for everyday use.
• Helps prevent further cabinet or door damage caused by makeshift grips or tape.
• Works with the door latch and hinge assembly to maintain normal door function.

• Disconnect power and empty door shelves before starting to avoid items falling.
• Remove mounting screws and/or trim as required; install handle in the original orientation.
• Tighten fasteners securely but avoid over-torquing to prevent cracking the handle.

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.