Parts for Frigidaire FGTR1845QE2: 02 - Door Parts

The Freezer Door Gasket is an OEM part for Frigidaire refrigerators, specifically designed to create an airtight seal around the freezer door. This gasket prevents warm air from entering and cold air from escaping the freezer compartment, ensuring efficient cooling and energy efficiency. Made from durable rubber, this gasket is flexible yet strong, designed to withstand the constant opening and closing of the freezer door.  

Causes of a bad Freezer Door Gasket can include wear and tear over time, exposure to excessive moisture leading to mold or mildew buildup, or damage from cleaning products or sharp objects. 

Symptoms of a bad Freezer Door Gasket include:

• Visible cracks, tears, or warping in the gasket.
• Condensation or ice buildup around the door edges.
• The freezer struggles to maintain the set temperature.
• Increased energy consumption as the freezer works harder to keep cold.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replaces a worn refrigerator door seal on the fresh-food compartment to restore a tight, even seal. Helps maintain cold temperatures, reduce condensation around the door, and cut energy loss when the old gasket is torn, warped, or gapped.

What it does

• Creates a continuous seal around the fresh-food door to keep cold air in.
• Helps prevent warm-air leaks that cause temperature swings.
• Reduces moisture/sweating along the door edge.
• Addresses gaps, tears, cracks, or a gasket that won’t lie flat.

What’s included
One refrigerator door gasket for the fresh-food door (black).

Install notes

• Unplug the refrigerator before starting.
• Warm the new gasket (soak in warm water or use low-heat hair dryer) to relax folds.
• Seat the gasket lip fully into the door channel—start at the corners and work around.
• Close the door and check for uniform contact (paper-pull test); level/adjust hinges as needed and allow 24 hours for the gasket to conform.

This clear refrigerator bin stores and organizes food items on a shelf or in a door, keeping groceries contained and easy to access. It replaces cracked, broken, or missing bins so items stop shifting or falling. What it does:

• Holds and organizes produce, deli items, or packaged foods to maximize usable shelf space
• Prevents items from sliding and reduces spills inside the refrigerator
• Restores proper fit where a damaged or missing bin causes gaps or instability
• Compatible with models that use a straight-fit clear storage bin design

• One clear refrigerator bin

• Remove all contents and open the shelf or door fully before installing
• Align bin with shelf rails or mounting slots and slide until it seats securely
• Do not force; if it does not seat easily, inspect for obstructions or misaligned rails
• Clean with mild soap and water; avoid abrasive pads or strong solvents that can damage the plastic

This replacement door bin mounts on the appliance door to hold items securely. Restore organized, usable storage when the original bin is cracked, loose, or missing, and help prevent items from tipping or falling as the door moves.

• Attaches to door liner rails to provide convenient, accessible storage and maximize space
• Replaces a bin that is cracked, warped, broken, or missing
• Common symptoms include broken end tabs, bin won't stay seated, wobbling/sagging, or items falling during door operation
• Matches the original fit for the designated door position on compatible models

• Remove contents; lift the old bin straight up and out of the door slots
• Align the new bin with the tabs/rails and press down until fully seated
• Verify the door closes freely; distribute weight evenly and avoid overloading
• If the bin is very cold, allow it to warm to room temperature before installation to reduce stress on the plastic

This small black plug/button covers a hinge or bearing access hole to restore a finished appearance and help keep out dirt and debris. It's a simple, inexpensive trim piece that maintains the appliance's look and helps protect internal components. What it does:

• Covers exposed hinge or bearing access holes for a clean, finished appearance
• Helps keep dust and debris out of hinge or bearing cavities
• Prevents snagging and reduces the chance of small items entering the opening
• Matches factory appearance and fit for a seamless repair

• Push-fit design; press into the hole until fully seated
• Keep away from small children — small part is a choking hazard

This replacement nameplate label restores the appliance's identification and rating information so you can read model, serial, and electrical data clearly. Helps when the original label is faded, damaged, or missing. What it does

• Displays model and serial numbers, electrical ratings and safety markings for identification and service
• Replaces faded, torn, or illegible factory labels so appliance data is readable
• Helps technicians and owners confirm correct specifications during repairs or replacement parts ordering
• Does not affect appliance operation; used for identification and information only

• One replacement nameplate label

• Clean and dry the surface before applying so the label adheres and lays flat
• Align carefully; many labels are adhesive-backed and are intended for single use
• Avoid placing over gaskets, vents, or moving parts; install where original label was located

This door stop limits the opening range of your refrigerator door to prevent overextension and hinge strain. Replace a worn or broken stop to restore controlled door movement and protect surrounding cabinetry from accidental impacts. What it does:

• Controls how far the door opens to prevent overextension and damage
• Helps maintain proper door alignment and reduces stress on the hinges
• Replaces cracked, deformed, or missing stops that no longer hold the door at its stop point
• Common symptoms include the door swinging too far, a hard "clunk" at full open, or visible damage to the stop

• 1 door stop

• Disconnect power; turn off water supply if your unit has a dispenser/ice maker
• Support the door before loosening any hinge fasteners to access the stop
• Note the stop's orientation and position; transfer any spacers and reinstall the same way
• Open and close the door to verify proper range and clearance before fully tightening fasteners

The Door Stop is an OEM part for Frigidaire refrigerators. This small part helps protect the appliance's door from damage and prevents it from impacting walls or adjacent cabinetry, ensuring the longevity and integrity of your refrigerator's exterior. 

Causes of a bad Door Stop can range from physical damage due to forceful door opening, to normal wear and tear from repeated use. In some cases, the mounting area for the door stop may become worn or damaged, affecting its ability to hold the door stop securely.

Symptoms of a bad Door Stop include:

• The refrigerator door swings open wider than usual
• Noticeable wear, damage, or breakage on the door stop
• Difficulty in opening or closing the door smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A small black replacement plug button that restores a clean, finished appearance and helps keep controls and openings free from dirt and moisture. Designed as a direct-fit cosmetic and protective cap for compatible appliance openings. What it does

• Covers exposed holes or button openings to prevent debris and spills from entering internal areas
• Restores the original look where a worn or missing plug detracts from the appliance finish
• Holds in place to protect underlying components from accidental contact
• Useful when replacing control bezels or trim that require a matching push-in cap

• Disconnect power to the appliance before performing any service work
• Press the plug button squarely into the opening until it snaps into place; no special tools typically required
• Inspect the mounting hole for damage or debris before installing to ensure a secure fit
• If the part does not seat properly, do not force it; verify correct part and orientation

INCLUDES 1 HANDLE AND MOUNTING HARDWARE

The Black Handle Kit is an OEM part for Frigidaire refrigerators. It includes new black handles that replace old or damaged ones. Doors and refrigerator components undergo frequent use which can cause handles to show wear through opening and closing motions over many cycles.

Causes of bad handles can be normal wear and tear like scratches, discoloration, loose or missing screws from repeated use. Excessive force when closing doors poses risk of cracks or breaks too.

Symptoms of bad handles include:

• Scratches, chips or discoloration of handle surfaces
• Loose, wobbly or unstable gripping feel
• Difficulty smoothly opening/closing doors due to poor handles
• Cracks or broken pieces that compromise function

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

INCLUDES 1 HANDLE AND MOUNTING HARDWARE

The Black Handle Kit is an OEM part for Frigidaire refrigerators. It includes new black handles that replace old or damaged ones. Doors and refrigerator components undergo frequent use which can cause handles to show wear through opening and closing motions over many cycles.

Causes of bad handles can be normal wear and tear like scratches, discoloration, loose or missing screws from repeated use. Excessive force when closing doors poses risk of cracks or breaks too.

Symptoms of bad handles include:

• Scratches, chips or discoloration of handle surfaces
• Loose, wobbly or unstable gripping feel
• Difficulty smoothly opening/closing doors due to poor handles
• Cracks or broken pieces that compromise function

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement mounting screw secures components and panels in refrigerators and freezers, restoring proper fit and stopping loose or rattling parts. Use when original screws are missing, stripped, or damaged. What it does:

• Fastens trim, panels, brackets or small components to the appliance frame
• Restores secure attachment to stop rattling or intermittent contact
• Replaces stripped, corroded, or missing screws to prevent parts from shifting
• Simple, direct replacement that matches the original mounting point

• Use the matching driver bit to avoid stripping the screw head
• Tighten until snug; do not overtighten to prevent thread damage
• Disconnect power to affected appliance areas before servicing if panels expose wiring
• If threads are damaged, replace the mating nut or tapped insert as needed

The Screw is an OEM replacement part for Frigidaire refrigerators. This small but essential component is used to secure various parts of the appliance, such as panels, brackets, or internal fixtures, ensuring the refrigerator's structural integrity and proper operation.

Over time, screws may become loose, stripped, or corroded due to regular use, environmental factors, or maintenance work. A damaged or missing screw can lead to misaligned parts or reduced stability of the appliance.

Symptoms of a bad or missing screw include:

• Loose or wobbly components within the refrigerator
• Panels or fixtures coming apart or misaligned
• Difficulty securing parts during maintenance or repair
• Rattling or unusual noises during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Hinge Bearing is an OEM part for Frigidaire refrigerators. It is designed to facilitate the smooth opening and closing of the refrigerator door by providing a pivot point for the door hinge. This bearing ensures that the door moves easily and remains properly aligned, helping to maintain a tight seal and optimal refrigerator performance.

Causes of a bad hinge bearing can include regular wear and tear from frequent use, exposure to moisture or temperature changes, and physical damage due to accidental impacts. Over time, these factors can cause the hinge bearing to wear out, become loose, or break, affecting the door's functionality.

Symptoms of a bad hinge bearing include:

• Difficulty opening or closing the refrigerator door
• The door not staying in place or sagging
• Unusual noises, such as squeaking or grinding, when the door is moved
• The door not sealing properly, leading to temperature fluctuations inside the refrigerator

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This genuine replacement screw restores a secure hold for panels, trim, or internal components. It replaces worn or missing fasteners so parts stay aligned and appliances operate safely. What it does:

• Fastens panels, brackets, or trim into place
• Replaces stripped, missing, or damaged screws
• Helps stop rattling, loose panels, or misaligned trim
• Fits OEM mounting locations that require the specified machine screw

• Use the correct driver to avoid stripping the head
• Hand-start the screw, then tighten to firm snug; do not over-torque
• Disconnect power to the appliance before accessing internal components
• If other fasteners are damaged, inspect and replace as needed

This part number contains one (1) screw.

The Door Handle Screw is an OEM part for Frigidaire refrigerators. This screw secures the door handle to the refrigerator door, ensuring a firm and stable grip for opening and closing the door.

Causes of a bad door handle screw can include regular wear and tear from frequent use, corrosion due to exposure to moisture, or damage from over-tightening or stripping. A faulty screw can lead to a loose or wobbly door handle, making it difficult to operate the refrigerator.

Symptoms of a bad door handle screw include:

• The door handle feeling loose or coming off
• Difficulty in securely tightening the handle
• Visible rust or corrosion on the screw
• Stripped threads on the screw or handle

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a service wrench used to loosen and tighten appliance fasteners for maintenance and repairs, making access and part replacement easier for technicians and DIYers. Durable tool designed for specific appliance fastener sizes. What it does:

• Provides the correct fit and leverage for removing or installing designated appliance nuts, bolts, and fittings
• Helps safely access internal components during service and part replacement
• Reduces risk of rounding fasteners compared with improvised tools
• Useful for routine maintenance tasks and repair procedures that require a dedicated wrench

• One wrench

• Use the wrench only for its intended appliance fasteners; avoid excessive force
• Disconnect power and water to the appliance before beginning service
• Wear safety gloves and eye protection when working on appliances