Parts for Frigidaire TSK180EN4W: 02 - Door Parts

The Refrigerator Door Gasket is an OEM part for Frigidaire refrigerators. This gasket forms a seal around the refrigerator door, ensuring that cold air stays inside and warm air remains outside, maintaining the appliance's efficiency and keeping food fresh.The gasket measures approximately 44.6" X 30.69"

Causes of a bad door gasket can include regular wear and tear, mold or mildew buildup, and physical damage from repeated opening and closing of the door. 

Symptoms of a bad refrigerator door gasket include:

• Warm air entering the refrigerator, causing it to run more frequently
• Condensation or frost buildup inside the refrigerator
• Difficulty keeping the door closed
• Visible cracks, tears, or deformation in the gasket

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued and is no longer available.

Color: White

This is a replacement white refrigerator door designed to restore your fridge's exterior appearance and provide a solid mounting surface for internal liners and hardware. It helps return the cabinet to proper alignment and aesthetics. What it does:

• Replaces a damaged, dented or cracked exterior refrigerator door panel
• Restores proper door fit and helps the door close evenly
• Provides a fresh, clean finish when the original door is chipped, scratched, or discolored
• Serves as the mounting surface for door trim, gaskets, and hardware

• Intended for use as a direct replacement; remove power to the appliance before starting work.
• Door may ship without handles, hinges, gaskets, or fasteners unless those items are explicitly listed as included—verify parts needed before installation.
• Two people are recommended for removal and installation due to door size and weight.
• Follow OEM instructions for hinge alignment and torque to ensure proper sealing and operation.

Refrigerator handle end cap that covers the end of the door handle. Replace this cosmetic part if your original cap is cracked, broken, or missing.

Replacement mounting screw for refrigerator components and panels. Secures interior parts, shelves, or housing. Order when original is stripped, lost, or damaged.

Replacement screw for various appliances. Used to secure panels, components, or housing. Replace if stripped, corroded, missing, or damaged hardware.

This part has been discontinued by the manufacturer and is no longer available.

Size: Approximate 2.5 inches thick, 33 inches wide and 70 inches long.

This is a hanger-mount screw used to secure interior refrigerator components such as deli/meat pan hangers and shelf supports. It provides a simple replacement to restore secure mounting and proper shelf alignment. What it does:

• Secures hanger mounts or support brackets that hold deli/meat pans or shelves in place
• Replaces missing or stripped screws that cause loose or sagging shelves
• Restores proper fit so stored items sit level and components do not shift
• Works where a #8 x 1/2 in pan-head fastener is specified

• One screw

• Disconnect power or unplug the appliance before performing any service
• Use the correct sized screwdriver to avoid stripping the pan head
• Thread carefully and tighten until snug; do not overtighten to prevent damage to the mounting surface

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

Size: Approximate 2.5 inches thick, 33 inches wide and 70 inches long.