Parts for Ge JGRS06BEJ1BB: 04 - Door Parts

Replace a cracked or discolored oven door window with this black glass panel. It restores clear visibility into the oven and proper heat retention so you can monitor cooking without drafts, hot spots, or safety concerns.

• Forms the glass portion of the oven door, allowing you to view food while maintaining cavity temperature
• Replace if the panel is cracked, shattered, chipped, scratched, stained, or separating at the layers
• Damage can lead to poor visibility and heat loss from the door
• Black finish to match compatible models

• Disconnect power and allow the appliance to cool completely before servicing
• Wear cut-resistant gloves and eye protection; handle glass by the edges only
• Support the door; removal from the hinges may be required
• Transfer any trim, brackets, or nameplate from the original glass; snug fasteners without overtightening

This oven door gasket seals the gap between the door and oven frame to keep heat in and temperatures accurate. Replacing a worn door seal restores proper preheat and baking performance and reduces heat escaping around the door.

• Forms a continuous perimeter seal around the oven door opening
• Helps maintain set temperature and proper preheating
• Reduces heat, odors, and smoke leaking from the door edges
• Common signs of failure: frayed or flattened gasket, visible gaps, heat escaping, longer cook times or uneven results

• Safety first: Disconnect power or gas and let the oven cool completely
• Open or remove the door per your model's instructions for access
• Remove the old gasket and clean the channel or mounting points
• Install the new gasket evenly without stretching; confirm the door closes and seals uniformly

This 24-inch replacement door handle restores a secure, easy-to-grip pull for compatible refrigerators and freezers while matching black trim. It replaces damaged, cracked, or missing handles to improve appearance and everyday use. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, broken, or missing handles that affect function or looks
• Restores proper mounting alignment when original handle hardware has failed
• Helps prevent food loss and leaks caused by difficulty sealing the door

• Use basic hand tools; support the door during removal/installation to avoid injury or damage
• Do not overtighten fasteners — snug until secure to prevent cracking the handle
• Turn off power only if needed per appliance service instructions and when working near electrical components

This is the replacement front frame panel that restores the appearance and protective trim around an oven door. It gives a clean, finished look and helps protect the door edges from chips and wear. What it does:

• Replaces a cracked, dented, or scratched oven door front frame
• Restores a flush, finished edge around the oven door for improved appearance
• Helps keep door components and seals aligned and protected
• Can reduce drafts or gaps caused by damaged trim that affect door fit

• Install requires removing the oven door or loosening door fasteners; follow the appliance manufacturer's service instructions.
• Use proper tools and keep track of all screws and clips; some fasteners may be reused.
• Disconnect power to the appliance before starting any repair to avoid electrical hazards.
• If the door is heavy or awkward to handle, have a helper to support the door during removal and reinstallation.

This spacer is a small mounting shim used to position and support components inside the appliance for correct alignment and stable operation. It helps maintain part clearance and keeps assemblies seated where intended. What it does:

• Provides spacing between panels or components to ensure proper alignment
• Helps prevent rubbing, binding, or misalignment of moving parts
• Can reduce vibration or noise caused by improperly seated parts
• Useful when replacing or reinstalling components that require precise clearance

• Disconnect power before accessing internal components
• Use basic hand tools; keep track of fasteners and original part locations
• Replace only with the same spacer size and orientation for correct fit

This reinforcement plate restores structural support where the oven/range door or trim attaches, helping stop sagging and keeping panels aligned for proper sealing and appearance. What it does:

• Reinforces the mounting area so door or trim stays securely attached
• Restores alignment to reduce gaps, drafts, or uneven door closing
• Prevents further wear at stressed screw holes and mounting points
• Stops rattling or vibration caused by loose or damaged support

• Disconnect power before servicing and allow appliance to cool completely
• Remove appropriate access panels or door per the manufacturer instructions
• Handle edges carefully; fasten with original hardware and torque to OEM specs
• If mounting holes or surrounding parts are damaged, inspect and replace any worn hardware

This hex washer head screw secures appliance panels and brackets. The 10-16 x 0.812 size replaces missing or stripped hardware so components stay properly fastened, helping prevent looseness, rattling, and misalignment.

• Fastens metal panels, brackets, and components in compatible appliances
• Replaces a lost, damaged, or corroded screw to restore proper attachment
• Helps reduce vibration, noise, or loose-fitting parts caused by missing hardware
• Correct 10-16 thread and 0.812-inch length for specified mounting points

• Disconnect power; for gas models, also shut off the gas supply.
• Note the original screw's location and orientation before removal.
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing.
• Use a nut driver or socket that fits the hex head.

ST10-16 X 7/16"