Parts for Ge JSP34AW2AA: 03 - Door Parts

This insulating foam strip fits inside the refrigerator door frame to help seal the door and reduce air leaks. Replacing a worn or damaged insulator restores better temperature control and helps prevent frost buildup along the door. What it does

• Fills the gap between the door and cabinet frame to improve the seal and reduce cold air loss.
• Helps prevent frost and moisture buildup around the door frame.
• Can reduce compressor run time caused by inefficient door sealing.
• Addresses symptoms like warm spots on the door edge, visible gaps, or excess frost near the door.

• Disconnect power to the appliance before beginning any repair.
• Remove the door liner or inner panel as required to access the frame channel (follow your model's service instructions).
• Press or slide the insulator into the channel; adhesive or retainer clips may be used depending on model.

This replacement oven door gasket forms the heat-resistant perimeter seal around the door opening. Restores a tight seal to retain heat, support accurate temperatures, and reduce warm-air leakage for better baking performance.

• Creates the compressible seal between the oven cavity and door to keep heat in
• Helps the oven preheat efficiently and maintain even temperatures
• Reduces warm air and odors escaping around the door edge
• Common failure signs include fraying, flattening, gaps, longer preheat, or uneven baking

• Disconnect power and allow the oven to cool completely; wear gloves
• Open the door and remove the old gasket from its retainers/channels, noting clip locations and orientation
• Clean the groove/retainer; starting at the top center, press the new gasket in evenly without stretching and seat corners fully
• Close the door and check for uniform contact around the perimeter

This insulating foam strip fits inside the refrigerator door frame to help seal the door and reduce air leaks. Replacing a worn or damaged insulator restores better temperature control and helps prevent frost buildup along the door. What it does

• Fills the gap between the door and cabinet frame to improve the seal and reduce cold air loss.
• Helps prevent frost and moisture buildup around the door frame.
• Can reduce compressor run time caused by inefficient door sealing.
• Addresses symptoms like warm spots on the door edge, visible gaps, or excess frost near the door.

• Disconnect power to the appliance before beginning any repair.
• Remove the door liner or inner panel as required to access the frame channel (follow your model's service instructions).
• Press or slide the insulator into the channel; adhesive or retainer clips may be used depending on model.

This hex washer-head screw secures sheet-metal panels, brackets, and assemblies in your appliance. Replacing a missing, stripped, or rusted fastener restores a tight, rattle-free fit and helps keep components properly aligned during everyday use.

• Fastens panels, brackets, and assemblies to the chassis
• Helps maintain alignment and stability under normal vibration and heat
• Direct replacement for lost, damaged, or stripped hardware
• Common signs include loose or rattling panels, gaps/misalignment, or a rounded screw head

• Disconnect power; if servicing a gas appliance, also shut off gas and allow surfaces to cool
• Match the new screw to the original location; start threads by hand to avoid cross-threading
• Tighten snugly without overtightening to prevent stripping sheet metal
• Use an appropriate nut driver or socket for the hex head

ST10-16 X 7/16"

ST10-16 X 7/16"

A single replacement screw used to secure appliance components and restore proper fit. This OEM-design fastener replaces a missing or damaged screw so panels, brackets, or small assemblies stay properly attached. What it does

• Fastens panels, brackets, or small assemblies to maintain component alignment and stability.
• Replaces stripped, corroded, or lost screws that cause rattling or loose parts.
• Restores secure connections that can prevent vibration noise or component movement.

• One screw.

• Disconnect power and unplug the appliance before starting any work.
• Match screw head type and length to the original before installation; use the correct driver to avoid stripping.
• Tighten snugly but avoid over-torquing, which can damage threads or parts.

This flat-head 10-32 zinc screw secures panels and components on compatible appliances, providing a corrosion-resistant fastener for reliable mechanical fastening. Use when replacing stripped or missing panel screws to restore proper fit. What it does:

• Fastens control panels, trim, or small appliance components with a 10-32 thread size
• Zinc plating helps resist rust and wear in typical household environments
• Replaces missing, damaged, or stripped flat-head screws that prevent panels from seating correctly
• Fits applications that require a countersunk/flush head for a clean finish

• Use the correct 10-32 driver bit and moderate torque to avoid stripping the head or threads
• Ensure the screw is the correct length and head style for your application before tightening
• Disconnect power to the appliance and follow OEM safety instructions before servicing

Package of 12