Parts for Ge GFD55GSPR2RS: Door Parts

The Door Protect Cover is an OEM part for GE dryers. It acts as the outer door glass safeguarding the dryer door opening from external debris and impacts.

Causes of a bad door protection cover can include cracks or breaks from repeated door slamming over time. Warping from heat exposure inside the dryer cabinet is also possible.

Symptoms of a bad door protection cover include:

• Difficulty sustaining a secure door seal  
• Strange noises or vibrations emanating from the door area
• The door failing to latch fully in place during cycles
• Obstructed drum rotation from a misaligned protect cover

This genuine GE replacement part is compatible with Hotpoint, RCA and select Kenmore dryers.

This door cover is the outer panel that restores a clean, finished look to your appliance door and protects internal door components from damage. It replaces cracked, dented, or cosmetically worn covers to improve appearance and function. What it does:

• Shields internal door parts and hardware from bumps, spills, and everyday wear
• Helps maintain proper door alignment and appearance after front damage
• Reduces drafts and prevents debris from entering the door cavity when intact
• Common symptom: visible cracks, dents, or scrapes on the door exterior

• Unplug the appliance or disconnect power before starting any repair.
• Remove door screws or clips as needed; support the door to prevent dropping.
• Align the cover carefully and secure all fasteners to restore fit and finish.

The Door Assembly is an OEM part for GE dryers. This part allows easy access to load and unload your laundry. The door assembly ensures a secure seal when closed, preventing heat and moisture from escaping the dryer drum. It features a sturdy handle for convenient opening and closing.

A bad door assembly can occur due to wear and tear, damage, or faulty hinges or latches. If you notice symptoms such as difficulty in opening or closing the door, a loose or misaligned door, or heat escaping from the dryer drum, it may be time to replace this part.

Symptoms of a bad door assembly include:

• Difficulty in opening or closing the door
• Loose or misaligned door
• Heat escaping from the dryer drum

Restore the functionality and efficiency of your GE dryer by replacing the faulty door assembly with this genuine part. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This stainless steel machine screw secures appliance components and trim for a reliable, corrosion-resistant hold. Use it when replacing lost or damaged fasteners to restore proper fit and reduce noise or misalignment. What it does:

• Fastens panels, brackets, and small assemblies where a #8-28 threaded screw is required
• Provides a rust-resistant connection for wet or humid appliance areas
• Helps stop rattling, loose trim, or misaligned parts caused by missing or stripped screws

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully by hand to avoid cross-threading; tighten until snug—do not overtighten
• Keep removed screws organized to ensure correct reassembly

This handle spacer fits between the door handle and the outer door panel on select front-load dryers. It restores the correct standoff so the handle mounts securely, reducing wobble and helping the door open and close smoothly.

• Maintains proper spacing and alignment between the handle and door panel
• Helps prevent handle wobble, rubbing, or sagging
• Replaces a cracked, worn, or missing spacer
• Common symptoms include a loose or uneven handle and difficulty opening/closing the door

• Disconnect power before servicing
• Support the door/handle, then remove the handle screws
• Note the spacer's orientation and location before removal; install the new spacer the same way
• Tighten screws snugly without overtightening; verify smooth door and latch operation

This GE Door Hinge is an OEM replacement part for GE washing machines. Designed to match the exact specifications of your GE appliance, this door hinge ensures smooth and reliable operation of the washing machine door. 

The need for a replacement usually arises when the existing hinge suffers from wear and tear, accidental damage, or corrosion. A bad door hinge can lead to issues with the door closing properly, which might affect the washing machine's functionality or cause water leakage.

Symptoms of a bad Door Hinge include:

• Difficulty in closing or opening the washing machine door.
• A door that hangs unevenly or appears misaligned.
• Unusual noises or resistance when moving the door.
• Visible wear, rust, or damage on the hinge.
• Water leakage around the door area.

This GE OEM replacement part is compatible with Hotpoint, RCA, and Kenmore models.

The Door Latch is an OEM part for GE dryers. It functions to securely fasten the dryer door shut during drying cycles. The latch fastens the door closed using a tension-based locking mechanism that engages automatically when closing the door.

Causes of a bad door latch can include loose or worn parts from continuous use over time. The locking mechanism may become improperly aligned or miscalibrated, inhibiting the secure closure of the door.

Symptoms of a faulty door latch include:

• Inability to start cycles with the door ajar
• Excessive moisture escaping around the edges of the poorly sealed door during drying
• Loud banging sounds from an improperly closing door
• Door popping open unintentionally mid-cycle 

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This 10-32 screw with a hex-washer head fastens panels, brackets, or components as specified by the manufacturer. Replacing worn or missing hardware restores a secure fit and helps reduce vibration, rattling, and loosening during operation.

• Provides 10-32 machine-thread fastening at the designated mounting point
• Hex-washer head helps distribute load for a tight, reliable clamp
• Replace if the original is missing, stripped, corroded, or won't stay tight
• Helps address loose panels/brackets, vibration, or rattling noises

• Disconnect power before servicing; if working on a washer, also shut off the water supply
• Use a driver or nut driver that matches the screw head
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Reinstall any original hardware in the same order it was removed