Parts for Ge GFD85ESPN1DG: Door Parts

The Door Protect Cover is an OEM part for GE dryers. It acts as the outer door glass safeguarding the dryer door opening from external debris and impacts.

Causes of a bad door protection cover can include cracks or breaks from repeated door slamming over time. Warping from heat exposure inside the dryer cabinet is also possible.

Symptoms of a bad door protection cover include:

• Difficulty sustaining a secure door seal  
• Strange noises or vibrations emanating from the door area
• The door failing to latch fully in place during cycles
• Obstructed drum rotation from a misaligned protect cover

This genuine GE replacement part is compatible with Hotpoint, RCA and select Kenmore dryers.

The Door Cover is an OEM part for GE dryers. Located on the external door, this cover protects the door lining while enhancing the dryer's aesthetic. It is responsible for safely concealing inner components from external impact or damage. 

Causes of a bad door cover can include cracks, chips, or discoloration from repeated opening and closing of the dryer door or other impact damage over time. Exposure to cleaning chemicals may also affect the integrity of the cover.

Symptoms of a bad door cover include:  

• Loose fit that does not properly cover the door lining
• Cracked, chipped, or broken door cover material
• Visible damage or deterioration affecting appearance
• Warping or sagging that prevents the door from closing fully

This part is compatible with Hotpoint, RCA, and select Kenmore dryer models.

This Dryer Door is an OEM part for GE dryers. It is designed to provide a secure and airtight closure for the dryer, ensuring optimal performance and energy efficiency. 

The need for a replacement dryer door can arise from physical damage, wear and tear, or seal degradation. A compromised door can lead to several operational issues.

Symptoms of a malfunctioning Dryer Door include:

• Difficulty in closing the door securely, or it pops open during cycles.
• Noticeable gaps or misalignment when the door is closed.
• Increased drying times, due to heat escaping.
• The dryer stops or pauses, triggered by door sensor issues.
• Visible wear or damage to the door or its components.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This stainless steel machine screw secures appliance components and trim for a reliable, corrosion-resistant hold. Use it when replacing lost or damaged fasteners to restore proper fit and reduce noise or misalignment. What it does:

• Fastens panels, brackets, and small assemblies where a #8-28 threaded screw is required
• Provides a rust-resistant connection for wet or humid appliance areas
• Helps stop rattling, loose trim, or misaligned parts caused by missing or stripped screws

• Disconnect power to the appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread carefully by hand to avoid cross-threading; tighten until snug—do not overtighten
• Keep removed screws organized to ensure correct reassembly

This handle spacer fits between the door handle and the outer door panel on select front-load dryers. It restores the correct standoff so the handle mounts securely, reducing wobble and helping the door open and close smoothly.

• Maintains proper spacing and alignment between the handle and door panel
• Helps prevent handle wobble, rubbing, or sagging
• Replaces a cracked, worn, or missing spacer
• Common symptoms include a loose or uneven handle and difficulty opening/closing the door

• Disconnect power before servicing
• Support the door/handle, then remove the handle screws
• Note the spacer's orientation and location before removal; install the new spacer the same way
• Tighten screws snugly without overtightening; verify smooth door and latch operation

This GE Door Hinge is an OEM replacement part for GE washing machines. Designed to match the exact specifications of your GE appliance, this door hinge ensures smooth and reliable operation of the washing machine door. 

The need for a replacement usually arises when the existing hinge suffers from wear and tear, accidental damage, or corrosion. A bad door hinge can lead to issues with the door closing properly, which might affect the washing machine's functionality or cause water leakage.

Symptoms of a bad Door Hinge include:

• Difficulty in closing or opening the washing machine door.
• A door that hangs unevenly or appears misaligned.
• Unusual noises or resistance when moving the door.
• Visible wear, rust, or damage on the hinge.
• Water leakage around the door area.

This GE OEM replacement part is compatible with Hotpoint, RCA, and Kenmore models.

The Door Latch is an OEM part for GE dryers. It functions to securely fasten the dryer door shut during drying cycles. The latch fastens the door closed using a tension-based locking mechanism that engages automatically when closing the door.

Causes of a bad door latch can include loose or worn parts from continuous use over time. The locking mechanism may become improperly aligned or miscalibrated, inhibiting the secure closure of the door.

Symptoms of a faulty door latch include:

• Inability to start cycles with the door ajar
• Excessive moisture escaping around the edges of the poorly sealed door during drying
• Loud banging sounds from an improperly closing door
• Door popping open unintentionally mid-cycle 

This GE replacement part is compatible with Hotpoint, RCA, and some Kenmore models.

This 10-32 screw with a hex-washer head fastens panels, brackets, or components as specified by the manufacturer. Replacing worn or missing hardware restores a secure fit and helps reduce vibration, rattling, and loosening during operation.

• Provides 10-32 machine-thread fastening at the designated mounting point
• Hex-washer head helps distribute load for a tight, reliable clamp
• Replace if the original is missing, stripped, corroded, or won't stay tight
• Helps address loose panels/brackets, vibration, or rattling noises

• Disconnect power before servicing; if working on a washer, also shut off the water supply
• Use a driver or nut driver that matches the screw head
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Reinstall any original hardware in the same order it was removed