Parts for Ge JBS60RK3SS: Door Parts

Decorative badge emblem that mounts on range control panel or door. Restores appliance exterior appearance when original is faded, scratched, or missing.

Replaces brittle, burned, or grease-soaked insulation inside your oven door. Restores the thermal barrier to reduce heat loss and exterior heat.

Insulation foam insert for range oven door. Installs behind the inner door panel. Replace if cracked, compressed, torn, or missing to restore proper fit.

Seals oven cavity to prevent heat loss during baking and broiling. Replace if worn, cracked, or heat escapes around door. Verify fit by model number.

Replace your range's oven door liner assembly if the inner panel is cracked, discolored, or damaged. Installs inside the door for a clean finish.

Retains oven door insulation in place on electric ranges. Replace if cracked, broken, or missing to secure door insulation and maintain proper fit.

This outer door panel replaces the decorative exterior panel on your microwave door. It restores a clean, factory appearance and provides proper support for the handle after dents, cracks, or finish damage.

• Forms the visible outer surface of the microwave door
• Provides mounting points for the door handle
• Helps protect inner door components and glass
• Common symptoms: dents, cracks, scuffs/discoloration, or broken handle mounts

• Disconnect power by unplugging the unit or switching off the breaker before service
• Wear cut-resistant gloves; panel edges can be sharp
• Transfer the existing handle and any reusable hardware/trim from the old panel as required
• After reassembly, verify the door closes and latches smoothly

Door pad gasket creates a seal between your oven door and front panel. Replace if worn, cracked, or causing heat loss. Confirm fit with your model number.

The Handle and End Cap Assembly is an OEM replacement part for GE ranges. It is a stainless steel colored handle with the mounting encaps already attached.

Causes of a bad handle and end cap assembly can include normal wear from frequent use over many years. Damage from accidental impacts is also possible.

Symptoms of a bad handle and end cap assembly include:

• Difficulty opening or closing the oven door smoothly  
• Excessive force required to engage the latching mechanism
• The door not sitting flush or properly sealing when shut
• Weakened hinges or handles prone to breakage
• Scratches, cracks, or deterioration appearing on surfaces

This OEM part is also compatible with some models produced by Hotpoint, Amana, and Sears Kenmore.

Secures exterior trim to your range door on the right side. Replace this bracket if cracked, broken, or missing to restore a flush, finished look.

This left-hand door handle bracket secures the refrigerator door handle to the door, restoring a stable grip and proper handle alignment. Durable replacement part helps stop a loose or wobbly handle and keeps the door operating smoothly. What it does:

• Mounts the door handle to the left side of the refrigerator door
• Provides a secure anchor to prevent handle movement or sagging
• Restores proper handle alignment for comfortable opening and closing
• Helps eliminate rattling or looseness when the door is used

• One left-hand door handle bracket

• Designed for direct replacement; inspect mounting screws and handle for wear before installing
• Use basic hand tools; avoid overtightening fasteners to prevent cracking the bracket
• Disconnect power only when working near electrical components; follow appliance safety guidance
• If screws or handle hardware are missing or damaged, replace those parts as well

This door hinge assembly connects the oven door to the range body, allowing it to open and close smoothly and hold its position when partially or fully open. It includes the spring-loaded mechanism that controls the door's movement and keeps it sealed shut during cooking. Replace this hinge if the oven door drops down when opened, won't stay closed, hangs unevenly, or if you hear grinding or popping sounds during operation.

Replace your range's cracked or cloudy door window assembly to restore visibility and protect the oven interior. Confirm fit with your model number.

ST10-16 X 7/16"

Black. 8-18 AB HXW 3/8

Replacement mounting spacer for electric ranges. Positions and supports panels to maintain alignment and proper fit. Replaces worn, missing, or damaged spacers.

Includes 12 washers.

10-32 threaded screw secures control panels, brackets, and internal components in electric ranges. Replace when stripped, missing, or loose.