Parts for Jenn-Air W104: 04 - Door Parts

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This part has been discontinued by the manufacturer and is no longer available.

The Oven Door Hinge is an OEM part for Whirlpool wall ovens and ranges. Located on both sides of the oven door frame, these metal hinges provide the pivoting connection that allows smooth opening and closing of the door during cooking cycles.

Causes of failure can include wear of the hinge joints from repeatedly bearing the weight of the heavy oven door over thousands of uses. Exposure to high heat during cooking may gradually deteriorate lubricating grease or materials.

Symptoms of faulty hinges include:

• Door rubbing or sticking during opening/closing
• Off-center alignment when shut or inability to fully latch
• Noisy squeaking or grinding emerging from hinges
• Hinges loosened from screws/fastenings or mechanisms seized

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

This replacement door handle restores a secure, comfortable grip for opening and closing the appliance door. Built to match the OEM fit and mounting points, it replaces worn, cracked, or broken handles to improve everyday use. What it does:

• Replaces a damaged or worn door handle so the door can be opened and closed easily
• Provides the correct mounting points and alignment for a factory fit
• Restores a secure grip and normal operation when original handle is loose, cracked, or broken
• Helps prevent further damage to the door edge or trim caused by using a broken handle

• Disconnect power (and water, for appliances with water connections) before starting any repair.
• Installation typically requires removing the inner door panel or trim; keep screws and fasteners organized.
• Hand tools only—avoid over-tightening fasteners to prevent cracking the replacement handle.

This oven door seal creates a tight, heat-resistant barrier between the oven door and front frame. A good seal helps the oven heat efficiently and prevents hot air from escaping into your kitchen.

• Cushions and seals the perimeter of the main oven door to contain heat
• Helps maintain stable cooking temperatures and energy efficiency
• Resolves issues like heat escaping around the door, uneven baking, longer preheat times, or visible gaps in the gasket
• Replaces a flattened, brittle, cracked, or torn door gasket

• Disconnect power and allow the oven to cool completely before service
• Open the door and remove the old gasket from its retaining clips or channel
• Press the new seal evenly into place, ensuring corners seat fully
• After installation, check door alignment and seal contact all around

The Screw is an OEM part for Whirlpool appliances. This specific screw is used in various locations within Whirlpool appliances, securing components and ensuring the stability and proper alignment of parts. It is designed to fit precisely and maintain a firm hold, contributing to the overall functionality and safety of the appliance.

Over time, screws can become worn or stripped due to regular use, corrosion, or over-tightening. 

Causes of a bad screw include wear and tear, exposure to moisture leading to rust, and over-tightening which can strip the threads.

Symptoms of a bad screw include:

• Loose or wobbly components
• Misalignment of parts
• Noise due to vibrating or loose parts
• Difficulty in securing or removing the screw

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.