Parts for Kenmore 253.29082991 (25329082991, 253 29082991): Door Parts

Replace your freezer door gasket to restore an airtight seal and prevent frost buildup. Worn or torn gaskets let warm air in, causing ice formation and soft food. Confirm fit with your model number before ordering.

By Frigidaire. Includes Freezer key 5303310289.

The Freezer Door Key is an OEM replacement part for Frigidaire refrigerators. This small but essential component is designed to securely lock the freezer door, preventing accidental openings or unauthorized access.

Symptoms of needing to replace the freezer door key include:

• Difficulty in locking or unlocking the freezer door
• The key not fitting properly or becoming stuck in the lock
• Visible wear, damage, or breakage of the key itself

Causes of a faulty freezer door key can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the locking mechanism itself.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore refrigerator models.

A single replacement mounting screw used to secure panels, brackets and trim on compatible appliances. Restores proper fit and stops rattling or loose components so panels stay aligned and stable. What it does:

• Fastens panels, brackets or trim pieces to appliance chassis
• Helps eliminate rattling, vibration noise, and loose or sagging panels
• Restores secure attachment after stripped or missing fasteners
• Works with the corresponding threaded hole or nut to hold parts in place

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug; do not overtighten to prevent thread or part damage
• Disconnect power to the appliance before servicing if panels expose electrical components
• Ensure that hardware is properly seated before tightening

Replace your worn freezer door gasket to restore an airtight seal, prevent cold air loss, and reduce frost buildup. Confirm fit by model number.

Quantity of 1 clip.

Note: See kit# 5303922007 and 5304406520.

A pressure-relief valve that allows air circulation and prevents vacuum formation in sealed freezer systems. Replace when experiencing difficulty opening the freezer door immediately after closing or poor temperature regulation.

Replace your freezer's door handle trim piece if it's cracked, broken, or missing. This trim attaches to the handle assembly for a finished look.

Replacement mounting screw for various appliances. Needed when original screws are stripped, lost, or damaged during repair or maintenance work.

Plastic plug insert for freezer door base. Covers screw holes or mounting points. Replace if cracked, missing, or worn to restore a clean appearance.

The refrigerator door tilt-out shelf end cap covers and secures the left end of adjustable door storage bins that tilt forward for easy access. Replace when the end cap cracks, breaks, or no longer securely holds the shelf in position.

Right-side end cap for refrigerator tilt-out door bin. Replaces cracked, broken, or missing end piece. Restores secure mounting and smooth pivoting.

This part has been discontinued and is no longer available.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

This cable clip secures a refrigerator's wire harness or control cables, keeping wiring routed and protected to prevent pinching or contact with moving parts. A small but important retainer for safe, tidy internal wiring. What it does:

• Holds and routes wire harnesses or cables to prevent interference with drawers, doors, or moving components
• Reduces wear and chafing on wires by keeping them away from sharp edges and heat sources
• Helps maintain reliable electrical connections by preventing strain on harnesses
• Commonly replaced when clips are broken, cracked, or missing and wires become loose or misrouted

• Turn off power to the appliance before accessing internal wiring
• Install by snapping clip onto designated frame or mounting boss and seating wire(s) into the clip
• Replace any damaged wiring or connectors discovered during installation

Foam insulation sleeve that wraps around the defrost drain tube. Replace if worn, missing, or damaged to prevent condensation and maintain proper insulation.