Parts for Kenmore 362.7175891 (3627175891, 362 7175891): Door Parts

Includes 12 speed nuts.

Left side broiler hinge for gas ranges. Replaces broken, worn, or missing hinges that prevent proper broiler door operation and alignment.

Right side broiler hinge for gas ranges. Replacement for broken, cracked, or worn hinges that keep the broiler door properly aligned and supported.

Secures and stabilizes your gas range broiler drawer, allowing smooth sliding and proper alignment. Replace if worn, broken, or missing.

Left side broiler panel for gas ranges. Replaces cracked, damaged, or missing side panels. Mounts to the broiler compartment interior wall.

Side broiler panel guide for gas ranges. Installs on the right side of the broiler cavity. Replace if cracked, broken, or missing to restore proper fit.

Broiler rack slide support that mounts inside your range oven cavity. Replace if bent, broken, or missing to restore smooth sliding and stability.

This is the right side broiler door spring. For left side use WB9K3.

Left side broiler door spring for gas ranges. Replaces cracked, broken, or worn springs that fail to hold the broiler door properly in position.

Protective liner panel for range storage or warming drawers. Replace if cracked, stained, warped, or missing to restore drawer appearance and function.

Includes 12 washers.

Spacer that fits between mating parts in your range or oven to maintain proper clearance and alignment. Replace if worn, missing, or damaged to prevent rubbing.

The Bumper is an OEM part for GE ranges. It is located on the sides of the oven drawer and serves as a cushion to prevent noise, vibration, and wear. As time goes on, regular use of the appliance can cause it to become damaged or worn out.

Causes of a bad bumper can include wear and tear from regular use, deterioration of the material over time, or damage from excessive force when closing the door.

Symptoms of a bad Bumper include:

• Excessive noise
• Difficulty in sliding the drawer
• Misalignment
• Wear, and increased friction

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Contoured washer trim secures and cushions range components, maintaining proper alignment and reducing wear. Replace if worn or damaged. Verify fit with your model.

Color: Black

Seals your oven door to retain heat and maintain proper cooking temperature. Replace if torn, brittle, or heat escapes. Clips into place in minutes.

Includes 12 screws.

Insulation pad that lines the oven door to retain heat and reduce exterior temperature. Replace if torn, compressed, or missing for proper efficiency.

Replaces cracked, shattered, or heat-damaged inner glass pane in your range oven door. Restores insulation, visibility, and protects from spills.

Insulation guard that installs inside the oven door assembly to protect internal components. Replace if cracked, torn, or missing during door maintenance.

Includes 12 screws.

Black trim piece that installs at the bottom edge of your range oven door. Replace if cracked, rusted, broken, or missing to restore appearance.

Replacement mounting screw for electric and gas ranges. Secures internal components and panels. Needed when original screws are stripped, missing, or lost.

This painted screw head is a cosmetic and protective cap that restores the finished look where a visible screw is used. It covers the screw head and helps match surrounding black trim for a clean appearance. What it does:

• Covers and conceals a screw head to improve appearance of panels, trim, or bezels
• Helps protect the screw head from direct exposure and reduces visible wear
• Used when trim or panels show exposed or mismatched screw heads
• Common fix when screw heads are scratched, discolored, or visually distracting

• Use the matching screw and press or snap the cap into place over the screw head
• Disconnect power and remove any panels only as recommended by your appliance manual before working near electrical components
• Avoid forcing or prying the cap; if tight, gently ease it on to prevent breakage
• Replace any damaged caps with the exact part to maintain fit and finish

Endcap for range storage drawer. Installs at drawer end to provide finished edge and structural support. Replace if cracked, broken, or missing.

This is a black plastic end cap that attaches to the right side of the oven door vent trim on a range. It provides a finished appearance and helps direct airflow through the door vent area. Replace this end cap if it is cracked, broken, discolored, or missing, which can affect the look of the range and proper venting around the oven door.