Parts for Kenmore 790.49409316 (79049409316, 790 49409316): Door Parts

Trim piece for range control panel. Replaces cracked, chipped, or discolored trim around the control area. Restores a finished appearance to your range.

This complete refrigerator door assembly replaces a damaged or bent door to restore proper sealing, operation, and appearance. It provides a factory-fit replacement that mounts in place of the original door. What it does:

• Replaces a warped, dented, or non-closing refrigerator door to help restore proper sealing and temperature control
• Restores hinge mounting points and latch alignment so the door opens and closes correctly
• Improves the appliance's exterior appearance by replacing cosmetically damaged doors
• Works with existing inner components when those parts are not damaged

• Disconnect power and remove food from shelves as needed before starting work
• Door assemblies can be heavy—have a helper and use proper lifting technique
• Follow OEM service manual or instructions for hinge alignment, fasteners, and torque sequence

This complete freezer door assembly replaces a damaged or dented freezer door to restore a proper seal and finish. It provides the outer panel, inner liner, and factory-aligned mounting points for a like-for-like replacement. What it does:

• Replaces a bent, cracked, or cosmetically damaged freezer door to restore appearance and function
• Helps maintain proper temperature by allowing the door to seal correctly
• Restores factory hinge/mount alignment for smooth opening and closing
• Prevents cold air leaks and reduces frost buildup when door seals are intact

• High-level replacement; two people recommended to support and align the door safely
• Remove power to the appliance before beginning work and follow OEM disconnection procedures
• Keep fasteners and hinge hardware organized; reuse original brackets unless new hardware is explicitly included
• If gasket/trim is damaged, inspect and replace separately (not necessarily included)

Sound dampening insulation for wall ovens. Replaces worn, damaged, or missing insulation that reduces noise and heat transfer during operation.

Oven won't maintain temperature or exterior gets too hot? This insulation blanket contains heat and protects nearby components. Moderate DIY repair.

This is the inner glass panel that sits on the inside of the oven door assembly. It helps contain heat within the oven cavity and works with the outer glass to provide insulation for efficient cooking. Replace this panel if it is cracked, shattered, or has developed visible damage that could compromise heat retention or safety.

The Hinge is an OEM component specially designed for Frigidaire wall ovens. Responsible for securely mounting the heavy oven door during continuous opening/closing cycles, it ensures safe, reliable use.

Constant load stress from opening doors causes typical wear degrading precision fit reducing function over years of use. Oven access suffers from misaligned closures.

Symptoms indicating hinge issues involve:  

• Difficulty fully opening or stabilizing door position
• Noisy or off-center door alignment disturbing recipes  
• Sagging or loose door fit risking accidental closing 

Causes relate to normal metal component fatigue from sustained weight bearing multiplied by every use cycle. Impacts damage lubrication preventing smooth pivoting.

Replacing with this OEM Frigidaire hinge restores a secure, balanced opening for convenient recipe checks. Compatibility also fits some Kenmore, Gibson, and Electrolux wall ovens renewing a well-supported entrance for safety and long-lasting enjoyment. 

Mounting spacer positions and supports range components for proper alignment. Replace if worn, cracked, or missing to restore correct panel fit.

Secures and routes wiring cables inside your range or oven. Replace this retainer bracket if it's cracked, broken, or missing to properly support cables.

Metal support bracket that secures and stabilizes range components. Replaces broken, bent, or missing brackets to restore proper panel alignment.

This is a replacement screw used to secure appliance panels and components. It restores proper fastening so panels, trim, or assemblies stay tight and reduce vibration or rattling. What it does

• Fastens panels, brackets, or trim to the appliance chassis
• Helps stop loose or vibrating panels and trim pieces
• Restores proper alignment where a missing or stripped screw causes gaps or movement
• Use when the original screw is missing, damaged, or corroded

• One replacement screw as shown

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing which can strip threads or crack plastic
• Keep removed screws in a safe place; this screw matches the original before installation

Fastens panels, brackets, and covers inside your range or oven. Replace this screw if missing, stripped, or rusted to secure components properly.

Spacer that maintains proper gap between components in your range or oven assembly. Replace if missing, worn, or damaged to restore correct fit and alignment.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.