Parts for Maytag MGDE251YL0: 05 - Door Parts

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

This door seal is the refrigerator door gasket that helps maintain a tight seal to keep cold air in and reduce energy loss. Replacing a worn or torn gasket helps the appliance cool efficiently and protect stored food. What it does

• Forms an airtight barrier around the refrigerator door to prevent warm air from entering
• Helps maintain consistent internal temperature and efficient operation
• Reduces frost buildup and cycling caused by a leaking seal
• Commonly shows symptoms like visible cracks, tears, flattening, or a door that won't close snugly

• One refrigerator door gasket

• Inspect the door frame and strike surfaces; clean mounting channel before installing the new gasket
• Warm the gasket slightly or use recommended installation tools to ease fitting into the channel
• Check alignment and closure after installation; replace if mounting clips or retainer are damaged
• Disconnect power only if required by your model and follow all safety precautions

This replacement screw secures appliance components as designed by the manufacturer. Installing a new fastener restores a tight fit when the original is missing, stripped, or corroded, helping prevent vibration and misalignment during use.

• Fastens brackets, panels, or assemblies in the specified locations
• Replaces missing, stripped, or rusted hardware
• Helps maintain proper alignment and reduce vibration/noise
• Common signs you need this part: loose components, rattling, or a screw that won't tighten

• Disconnect power and turn off water supply before servicing
• Match the screw to its original location; length and thread engagement
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any original washers or spacers that were installed with the screw

This is a replacement sheet-metal screw used to secure panels and components on compatible Whirlpool appliances. It provides a reliable fasten point for reattaching trim, brackets, and access panels after service. What it does:

• Secures appliance panels, brackets, and smaller components to the cabinet or frame
• Helps restore original fit and finish after repairs or part replacement
• Prevents rattles or loose panels when properly installed
• Matches OEM thread size and head style for a correct fit

• Turn off and unplug the appliance before removing panels or installing hardware
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid over-torquing to prevent thread damage or warped panels

This is a replacement outer door panel that restores the appliance's appearance and provides a secure, functional door surface. It replaces a damaged or worn door panel so the unit closes and looks like new. What it does:

• Replaces a cracked, dented or cosmetically damaged outer door panel
• Restores proper door alignment and surface integrity
• Helps the door close smoothly and reduces drafts or gaps caused by warped panels
• Returns the appliance to original appearance for a clean, finished look

• One outer door panel as shown

• Door removal may require lifting, hinge release, or trim removal
• Power off and unplug the appliance before attempting any repairs to avoid electrical or injury hazards
• Handle panel edges carefully to avoid cuts and protect the finish from scratches
• Use OEM fasteners and follow the manufacturer's alignment/torque guidance when reassembling

Self-locking, phillips screw.

This is a replacement outer cabinet door that restores the refrigerator's sealed closure and appearance. Replacing a damaged or dented door helps maintain proper cooling and keeps contents protected while improving the appliance's look. What it does:

• Replaces a cracked, dented, or bent outer door panel to restore fit and appearance
• Helps the door close and seal properly to maintain interior temperature
• Stops drafts and reduces moisture/condensation caused by poor door fit
• Prevents further wear to hinges, gaskets, and internal components from a misaligned door

• One complete outer door panel

• Door assemblies can be heavy or awkward
• Disconnect power and empty the appliance before removing the old door
• Retain and transfer existing hinges, screws, trim, and gasket unless new hardware is explicitly included
• Verify hinge alignment and gasket seating during reinstallation to ensure a proper seal

Outer door glass that restores the oven door viewing window and replaces cracked, chipped, or broken glass so the door functions safely and looks like new. What it does

• Replaces damaged or shattered outer door glass to restore a clear viewing window.
• Stops rattling or loose glass caused by broken mounting points or cracks.
• Helps maintain proper door appearance and user visibility into the oven cavity.
• Useful when glass has visible chips, cracks, or safety concerns.

• One outer door glass

• Disconnect power to the appliance before beginning any repair.
• Handle glass with heavy-duty gloves and eye protection; glass can break unexpectedly.
• Replacing this part typically requires removing the oven door and disassembling panels—follow the OEM service manual or instructions.
• Inspect and replace any worn clips, screws, or seals as needed; do not overtighten fasteners.

The Door Latch Kit is an OEM replacement part for Whirlpool washers. This component is responsible for securely locking the washer door during the wash cycle, preventing it from opening unexpectedly and ensuring a safe and efficient operation.

Symptoms of needing to replace the door latch kit include:

• Difficulty in closing or latching the washer door
• Door opening unexpectedly during the wash cycle
• Leaks or water seeping due to an improper door seal
• Excessive wear or damage to the latch components

Causes of a faulty door latch kit can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the door alignment or strike plate.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.

This retainer clip secures small appliance components in place to prevent movement and ensure proper alignment for reliable operation. It's a simple replacement that restores lost or broken mounting support. What it does:

• Holds and stabilizes the attached component or assembly to prevent shifting during use
• Maintains proper alignment for connected parts to reduce wear and noise
• Commonly used where a small plastic or metal clip is needed for secure mounting
• Can address symptoms like loose panels, rattling, or parts that won't stay seated

• One retainer clip

• Disconnect power to the appliance before attempting any repair
• Remove surrounding panels as needed to access the clip; small trim tools may help
• Replace the broken retainer with the new clip and verify the secured component is seated correctly

The door seal forms the primary gasket around the door opening on horizontal-axis machines, creating a tight barrier that keeps contents contained and prevents gaps that can lead to leaks, odors, and poor performance. What it does

• Seals the perimeter of the door opening to contain wash water and suds
• Helps the door close flush and maintain a consistent, leak-free seal
• Common symptoms: water leaking at the door area, visible tears or cracks in the seal, persistent mildew/odors around the gasket, or a door that won't seal properly

• 1 door seal

• Disconnect power and shut off water supply before servicing
• Remove the front panel/retaining bands as needed to access the seal
• Note orientation and drain holes at the bottom; press the seal fully into its groove all the way around
• Reinstall retainers, ensure the door closes flush, and run a short test to check for leaks