Parts for Maytag MGDE400XR1: 05 - Door Parts

Adhesive information label for dryers. Replaces worn, faded, or missing labels to restore readable model, serial number, and safety details.

Connects dryer door to cabinet, allowing smooth opening and closing. Replace if hinge is broken, worn, bent, or causing door misalignment issues.

This factory fastener secures appliance components such as panels, brackets, and handles. Replacing a missing or damaged screw restores a tight fit, reduces rattles, and helps keep parts aligned for smooth, reliable operation.

• Secures components to the appliance frame or assemblies
• Helps maintain alignment and structural stability
• Replaces missing, rusted, or stripped hardware
• Common symptoms include loose/wobbly handles or panels, rattling/vibration noises, or a visibly missing screw

• Disconnect power before servicing
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten; snug until secure
• Replace any that are corroded or stripped for an even hold

Retainer link that secures cables in your dryer. Installs to hold wiring harnesses in place. Replace if cracked, broken, or missing to restore proper fit.

Secures dryer components in place to prevent movement and maintain proper alignment. Replace if your retainer clip is cracked, broken, or missing.

This replacement screw secures appliance components as designed by the manufacturer. Installing a new fastener restores a tight fit when the original is missing, stripped, or corroded, helping prevent vibration and misalignment during use.

• Fastens brackets, panels, or assemblies in the specified locations
• Replaces missing, stripped, or rusted hardware
• Helps maintain proper alignment and reduce vibration/noise
• Common signs you need this part: loose components, rattling, or a screw that won't tighten

• Disconnect power and turn off water supply before servicing
• Match the screw to its original location; length and thread engagement
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any original washers or spacers that were installed with the screw

This replacement plug seals a drain or access opening to prevent leaks and keep refrigerant/condensate and debris where they belong. Fits service openings on compatible Whirlpool appliances to restore a watertight seal. What it does:

• Seals a drain, access hole, or service opening to stop water or debris from leaking out
• Helps maintain proper condensate routing and prevents pooling inside the cabinet
• Prevents pests and dust from entering through unused openings
• Simple, non-electrical part that restores the original seal and function

• One plug

• Disconnect power to the appliance before servicing; follow all safety procedures
• Press the plug firmly into the opening until fully seated; use hand pressure only unless otherwise specified
• Inspect for proper sealing and test with a small water flow before reassembling the appliance

Replace stripped or missing screws causing loose panels or rattling during cycles. This self-locking Phillips screw secures internal components. Easy 5-minute fix.

This is a tempered glass window for the oven door that provides a clear view of cooking without opening the door and helps contain oven heat for more consistent baking results. What it does:

• Replaces a cracked, shattered, scratched or fogged oven door viewing window
• Allows you to monitor food without opening the door, reducing heat loss
• Helps the door maintain proper thermal barrier and appliance efficiency
• Restores a safe, intact barrier between the oven cavity and the kitchen

• Disconnect power (and gas if applicable) and allow the oven to cool completely before beginning.
• Handle glass with cut-resistant gloves and eye protection; glass edges may be sharp.
• Installation typically requires removing the oven door and detaching inner panels—follow the oven's service instructions.
• Inspect and replace any worn door gaskets or mounting hardware as needed; test the door for secure fit and proper operation after installation.

Replace your worn dryer door seal to prevent air leaks and maintain efficient drying. This rubber gasket creates a tight barrier around the door opening. Confirm fit with your model number before ordering.

Sheet metal screw secures panels, brackets, and trim on washers, dryers, and laundry appliances. Replace when stripped, missing, or rusted during repair.

Replace your worn dryer door seal to restore a tight closure, contain heat and moisture, and eliminate rattling or squeaking. Easy snap-in install.

The Door Latch Kit is an OEM replacement part for Whirlpool washers. This component is responsible for securely locking the washer door during the wash cycle, preventing it from opening unexpectedly and ensuring a safe and efficient operation.

Symptoms of needing to replace the door latch kit include:

• Difficulty in closing or latching the washer door
• Door opening unexpectedly during the wash cycle
• Leaks or water seeping due to an improper door seal
• Excessive wear or damage to the latch components

Causes of a faulty door latch kit can include normal wear and tear over time, physical damage due to impact or mishandling, or issues with the door alignment or strike plate.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washer models.