Parts for Whirlpool ER8GHKXMS03: 02 - Door Parts

This genuine replacement handle endcap restores the finished edge of a refrigerator door handle, improving grip and appearance. Durable molded plastic matches white handle trims for a seamless look. What it does:

• Replaces a worn, cracked, or broken handle endcap to restore handle fit and appearance
• Secures the handle end and helps maintain proper handle alignment
• Helps eliminate rattling or loose-feeling handle edges
• Designed to match factory white finish for a cohesive look

• Basic hand tools required; your refrigerator's service manual for access steps
• Remove and retain any mounting hardware; replace only with OEM-specified fasteners
• Avoid forceful prying to prevent damage to the door or surrounding trim

This small black door stop shim helps position and stabilize the appliance door for correct alignment and smoother closing. It replaces a worn or missing shim to reduce door gaps and rubbing against the cabinet or frame. What it does:

• Centers and supports the door stop so the door closes evenly and seals properly.
• Prevents door-to-cabinet rubbing, scraping, or uneven wear on hinges and seals.
• Helps eliminate minor misalignment that can cause noise or uneven gaps.
• Compatible where the OEM diagram lists a door stop shim in the hinge/stop assembly.

• One black door stop shim

• High-level replacement: typically installs at the door stop or hinge area; may slide or snap into place—retain original orientation.
• Always support the door during removal/installation to avoid dropping or damaging the door or hinges.
• If the repair requires removing trim or hinge fasteners, keep fasteners organized and follow the appliance diagram.
• For any work near electrical components, unplug the appliance or switch off power at the breaker first.

The door stop shim positions the stop flush and fine-tunes the door's opening limit. Replacing a worn or missing shim helps restore smooth door operation and protects nearby surfaces from over-travel or rubbing.

• Provides correct spacing behind the door stop for proper alignment
• Helps limit the door swing to the intended stop position
• Can reduce wobble, play, or clicking at the stop point
• Replaces cracked, deformed, or missing shim components

• Disconnect power and support the door as needed to prevent strain
• Remove the door stop fastener(s) and note the original shim orientation
• Place the new shim behind the stop; reinstall hardware and tighten without overtightening
• Open and close the door to confirm stop angle and clearances

This genuine replacement handle endcap restores the finished edge of a refrigerator door handle, improving grip and appearance. Durable molded plastic matches white handle trims for a seamless look. What it does:

• Replaces a worn, cracked, or broken handle endcap to restore handle fit and appearance
• Secures the handle end and helps maintain proper handle alignment
• Helps eliminate rattling or loose-feeling handle edges
• Designed to match factory white finish for a cohesive look

• Basic hand tools required; your refrigerator's service manual for access steps
• Remove and retain any mounting hardware; replace only with OEM-specified fasteners
• Avoid forceful prying to prevent damage to the door or surrounding trim

Color: Black

The Refrigerator Door Gasket is an OEM replacement part for Whirlpool French-door refrigerators. Located around the perimeter of refrigerator door openings, it forms a critical insulating seal to maintain optimum interior temperatures.

Causes of a bad Refrigerator Door Gasket involve years of compression cycles compressing the door gasket material. Chemical deterioration from foods or spills could inhibit proper sealing as well.

Symptoms of a bad Refrigerator Door Gasket include:

• Sections inside the fridge appear warmer than expected
• Visible frost or condensation indicating temperature inconsistencies
• The cool air felt escaping around edges when doors are closed
• Inability to maintain a tight, insulating seal around doorways

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, and select Kenmore models.

The Fresh Food Door Gasket is an OEM part for Whirlpool refrigerators. It creates an airtight seal around the refrigerator door, helping to maintain the internal temperature and keep food fresh by preventing warm air from entering the refrigerator. This gasket measures approximately 44.70" X 27.16". 

You should replace the fresh food door gasket if it becomes worn out or damaged. Causes of a bad door gasket can include regular wear and tear, damage from frequent opening and closing of the door, and exposure to temperature fluctuations. Over time, the gasket may become brittle, crack, or develop mold.

Symptoms of a bad fresh food door gasket include:

• Warm air entering the refrigerator, leading to higher internal temperatures
• The refrigerator running more frequently or for longer periods
• Visible cracks, tears, or mold on the gasket
• Difficulty in closing the refrigerator door securely

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This genuine mounting screw secures appliance panels and components so they stay aligned and stable during use. A simple replacement that stops rattles and keeps parts properly fastened for safe, reliable operation. What it does:

• Fastens panels, brackets, or trim to the appliance frame
• Helps stop vibration noise and loose or misaligned parts
• Restores proper fit where an original screw is missing or damaged
• Prevents further wear caused by unsecured components

• Disconnect power to the appliance before beginning any repair
• Use the correct driver to prevent stripping the screw head
• Tighten until snug; avoid overtightening to prevent stripping threads or cracking plastic
• Replace like-for-like: if the original screw has a washer or special head, install the same type

This screw anchor is a small plastic fastener that secures panels and trim on appliances, preventing screws from stripping or pulling out. It provides a reliable anchor point for screws where threaded material is thin or absent. What it does:

• Creates a secure mounting point for screws in sheet metal, plastic or thin panels
• Helps prevent screw looseness, stripping, and parts that shift or rattle
• Commonly used to hold trim, panels, or interior components in place
• Works with compatible screws to distribute load and stabilize attachments

• Use the correct screw size and length; anchors are made for specific screw diameters—do not force oversize screws
• Align anchor in the prepared hole before driving the screw to avoid cracking the anchor or surrounding material
• Hand-start screws until seated, then tighten gradually—do not overtighten to prevent stripping or damage
• Disconnect power and follow appliance safety procedures before accessing internal panels

The Freezer Door Gasket is an OEM replacement part for Whirlpool side-by-side refrigerators. Located around the inside perimeter of the freezer compartment entrance, the gasket forms an insulating seal when the door closes. As an essential component ensuring efficient operation, the gasket helps maintain even sub-zero compartment temperatures.

Causes of a bad freezer door gasket can include cracking, flaking or splitting from repeated flexing as the door opens/closes, or impressions from dents compressing sealing surfaces. 

Symptoms of a bad freezer gasket include: 

• Noticeable frost buildup around the door edges indicating air leaks
• Difficulty latching the door fully with the locking mechanism 
• Increased running times for the compressor to recover temperatures
• Higher energy bills from the refrigerator working harder to chill

 This OEM Whirlpool part is also compatible with Kenmore, Maytag, Amana, and KitchenAid side-by-sides. 

The Bracket-Door Stop is an OEM replacement part for Whirlpool appliances. This zinc-finished bracket is designed to prevent the appliance door from opening beyond its intended range, protecting both the door and surrounding components from potential damage. It ensures the door stays secure and functions smoothly during regular use.

Symptoms of a bad Bracket-Door Stop include:

• The door overextending when opened
• Difficulty in maintaining the door's position
• Visible bending, cracking, or damage to the bracket

Causes of a failing Bracket-Door Stop can include repeated stress from excessive force when opening the door, normal wear over time, or accidental impacts. A damaged bracket can compromise the door's alignment and overall functionality.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: Black

Color: Bisque

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.