Parts for Whirlpool ET4WSMXKQ04: 02 - Door Parts

Replacement mounting screw for refrigerator panels, brackets, and trim. Restores secure fit when original screw is stripped, missing, or damaged.

White center section for refrigerator door handle. Replaces cracked, broken, or worn handle pieces. Installs with existing screws for secure door access.

The Screw is an OEM fastening component specifically designed for securing interior panels and assemblies of Whirlpool brand appliances. 

Causes of a problematic screw include stripping, corrosion, or shearing from repeated installations and removals during service procedures.

Symptoms of faulty screws include:

• Loosened or detached interior panels rattling behind appliance exteriors  
• Reduced structural integrity allowing unnecessary vibrations and noise

Compatible models include brands produced by KitchenAid, Maytag, and some Kenmore.

Replacement mounting screw for refrigerator panels, brackets, trim, and door handles. Restores secure fit when original fastener is missing, stripped, or corroded.

Seals the fresh food compartment door to prevent cold air leakage and maintain temperature. Replace if torn, cracked, or not sealing properly.

Size: 8-18 x 1/2 inch.

White screw cover cap for refrigerator door handles. Replaces missing, cracked, or yellowed covers. Installs on handle mounting screws for a clean finish.

Refrigerator name plate attaches to the exterior cabinet to display model information. Replace if plate is faded, cracked, peeling, or missing.

Plastic screw anchors secure panels, trim, and door handles on refrigerators. Replace missing, cracked, or stripped anchors to properly fasten components.

Front rail trim bar for refrigerator door shelves. Keeps jars and bottles secure. Replace if cracked, broken, loose, or missing to restore proper storage.

Protective thimble bushing that reinforces the hinge pin mounting hole in your freezer door liner. Replace if worn, cracked, or missing to stabilize hardware.

Front rail trim bar for refrigerator door shelves. Keeps jars and bottles secure. Replace if cracked, broken, loose, or missing to restore proper storage.

White button plug cap for refrigerators. Covers screw holes or mounting points on control panels and exterior surfaces. Replace when missing, cracked, or discolored.

Freezer door gasket creates an airtight seal to maintain temperature and efficiency. Replace if torn, cracked, or not sealing properly. Verify fit by model.

This May Be Longer Than Original If So Cut To Fit

This replacement screw secures panels, brackets, and other components in your appliance so they stay tight and properly aligned. Use it to replace missing, stripped, or rusted hardware and eliminate looseness, rattles, or gaps.

• Fastens parts to the cabinet/frame to maintain structural integrity
• Helps keep panels and assemblies aligned to reduce vibration and noise
• Replaces missing, damaged, or corroded screws during service
• Common fix for loose panels or components that no longer hold securely

• Disconnect power and shut off water or gas before servicing
• Match length and thread to the original screw for proper fit
• Hand-start threads to avoid cross-threading; tighten only until snug—do not overtighten
• Tighten them evenly to ensure proper alignment

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Secures the door shelf bar in refrigerator doors, providing a finished look and stability. Replace if cracked, broken, or missing to restore support.

Plastic endcap that fits on the end of refrigerator shelf trim for a finished look. Replace if cracked, broken, or missing to secure trim in place.

White refrigerator door handle for top-mount models. Replace your cracked, broken, or missing handle. Mounts with four screws for secure installation.

Front rail trim bar for refrigerator door shelves. Keeps jars and bottles secure. Replace if cracked, broken, loose, or missing to restore proper storage.